Tanaka THB-260PF, Инструкция по эксплуатации

Страница: 7 / 12

5
MODEL
THB-260PF / THB-260PF (S)
NGK BMR7A
23.9
Oiled foam filter system
By ANSI 68.0
By CEN 81.0
101
104
0.6
0.6
5.0
11.2
1.5
Assembly procedures
WARNING
Make sure the engine is turned off/stopped and not hot before
assembly.
Blow pipes to main body (Fig. 1)
Inspect the main body and accessories.
Connect straight pipe (1) and other pipe(s) securely. (See page 1 )
Align groove (2) in straight pipe with projection (3) on blower
housing (or another pipe) and slide the pipe onto the blower
housing (or another pipe).
Rotate the pipe clockwise to lock it into place.
Fan headed pipe to straight pipe (Fig. 2)
• Align groove (2) on the fan headed pipe (4) and projection (3) on
2
nd
straight pipe (1) and rotate the fan head in place.
NOTE (Optional)
Vacuum attachment is offered as an optional kit which converts the
hand-held blower into a vacuum cleaner.
For installation see optional kit ( THV-260) manual.
NOTE ; Safety future
If you try to open the dust cover (5) when engine is running, it will
automatically stop the engine. (Fig.3)
But never try to open the dust cover (5) when engine is running
even with this future, otherwise serious personal injury may occur.
Operating procedures
Fuel (Fig. 4)
WARNING
• This unit is equipped with a two-stroke engine. Always run
the engine on fuel, which is mixed with oil. Provide good
ventilation, when fueling or handling fuel.
• Fuel contains highly flammable and it is possible to get the
serious personal injury when inhaling or spilling on your body.
Always pay attention when handling fuel. Always have good
ventilation when handling fuel inside building.
Fuel
• Always use branded 89 octane unleaded gasoline.
• Use genuine two-cycle oil or use a mix between 25:1 to 50:1,
please consult the oil bottle for the ratio or Tanaka dealer.
• Only for the state of California at 50:1.
• If genuine oil is not available, use an anti-oxidant added quality
oil expressly labeled for air-cooled 2-cycle engine use(JASO FC
GRADE OIL or ISO EGC GRADE). Do not use BIA or TCW (2-stroke
water-cooling type) mixed oil.
• Never use multi-grade oil (10 W/30) or waste oil.
• Always mix fuel and oil in a separate clean container.
Always start by filling half the amount of fuel, which is to be used.
Then add the whole amount of oil. Mix (shake) the fuel mixture.
Add the remaining amount of fuel.
Mix (shake) the fuel-mix thoroughly before filling the fuel tank.
Fueling
WARNING
• Always shut off the engine and let it cool for a few minutes
before refueling.
• Slowly open the fuel tank, when filling up with fuel, so that
possible over-pressure disappears.
• Tighten the fuel cap carefully, after fueling.
• Always move the unit at least 3 m (10 ft.) from the fueling area
before starting.
• Do not smoke and/or allow flames or sparks near fuel when
handling or filling fuel.
• Always wash any spilled fuel from clothing immediately with
soap.
• Be sure to check for any fuel leaking after refueling.
Before fueling, clean the tank cap area carefully, to ensure that
no dirt falls into the tank. Make sure that the fuel is well mixed by
shaking the container, before fueling.
Starting the cold engine
CAUTION
Do not start if the pipe and dust cover are obstructed by the ground
or any other object.
1. Set ignition switch (6) to ON position. (Fig. 5)
*Push priming bulb (7) several times so that fuel flows through the
bulb or return pipe. (8) (Fig. 6)
2. Set choke lever to CLOSED position. (Fig. 7)
3. Pull recoil starter briskly, taking care to keep the handle in your
grasp and not allowing it to snap back. (Fig. 8)
4. When you hear the engine want to start, return choke lever to
RUN position (open). Then pull recoil starter briskly again.
WARNING
• Never start or run the engine inside a closed room or building
and/or near the inflammable liquid. Breathing exhaust fumes
can kill.
• Do not allow the rope to snap back in and always hold the
unit firmly.
NOTE
If engine does not start, repeat procedures from 2 to 4.
5. After starting engine, allow the engine about 2-3 minutes to
warm up before subjecting it to any load.
Starting the warm engine
Use only 1 and 3 of the starting procedure for cold engine.
If the engine dose not start, use the same starting procedure
as for a cold engine.
Operating blower (Fig. 9)
• A low speed should be used to blow leaves and dry grass.
• A medium speed should be used to clean wet leaves and grass.
• A high speed should be used when moving gravel, dirt or other
heavy materials.
WARNING
• Do not direct discharge of air toward people or pet.
• The unit should be operated in a well ventilated area.
• Never perform assembly or disassembly procedures with
engine running or serious personal injury may result.
• Never touch muffler, spark plug, or other metallic parts while
engine is in running or immediately after shutting off engine.
CAUTION
This blower has been designed and adjusted to be used with all
blowing pipes attached (See page 1). It must never be operated
without the straight pipe, and fan headed pipe.
NOTE
When you hear or feel strange sound or vibration, stop engine
immediately and check if anything blocks fans or pipes, If so,
remove it and check for damage.
Stopping (Fig. 10)
Decrease engine speed and run at an idle for a few minutes, then
turn off ignition switch.
NOTE
If the engine dose not stop, it can be forced to stop by setting
the choke lever to CLOSED position.
Before restarting the engine, ask Hitachi Authorized Service Centers
for repairs.