background image

I. FILM SLITTER 
 

This machine is equipped with safety film slitter in the back of the machine for trimming film in 

between sheets of laminated material. Simply slide the cutting edge across the film to remove the 

finished material.   

 

J. EMERGENCY STOP BUTTONS 

 

In case of emergencies, press either front or back red emergency buttons to immediately stop the 

motor and turn off the machine. To restart the machine, turn the power switch on and turn the button 

that was pressed clockwise to release it. Reset the machine’s temperature to the previous setting and 

continue with the laminating procedures. 

 

4    TURNING OFF THE LAMINATOR 

 

Upon completion of the laminating job, please press the “COOL” key to turn off the heat. We 

recommend turning off the machine only after the roller temperature is lower than 50°C (122°F). 

Make sure the rear fan switch is also turned off.   

 

In case you need to turn the machine off while the roller temperature is higher than 80°C (176°F), 

simply make sure the rollers are separated/not engaged, the fans are turned off and the handle is locked 

in at least the 3/16” position before turning the power switch off.   

 

5    CARE AND CLEANING   

   

This machine is for Office or Household use only. Any servicing, other than cleaning and user 

maintenance, should be performed by an authorized service representative. 

1.

 

Do not immerse in water. 

2.

 

To reduce the risk of fire or electric shock, do not remove the machine’s 4 rubber foot pads.   

3.

 

Keep your hands and cord away from hot parts of the machine during operation. 

4.

 

Never clean with scouring powders or hand implements. 

5.

 

Wipe clean with a soft cloth. 

 

 

 

 

 

Содержание TCC1200













Отзывы: