6.4"
162.6 mm
blades fully open
4"
101.6 mm
1"
25.4 mm
In Duct or
Flanged to Duct
Install Types
1.06"
27 mm
2"
50.8 mm
Extended Rear Flange
Install Type
TAMCO® Series 1000 SM meets the require-
ments for smoke dampers established by:
UL 555S/ULC-S112.1 File R16679
National Fire Protection Association:
NFPA Standards 80, 90A, 92, 101, 105
California State Fire Marshall Listing#:
3230-2116:0100
Leakage Rating:
Class 1
Operational
Rating:
Airflow: 2000 fpm
(10.2 m/s)
. Rated for airflow in either direction.
Temperature: 250°F
(121°C)
Pressure: 4” w.g.
(1 kPa)
static pressure differential
Fail Position:
Closed
STANDARD CONSTRUCTION:
1. Extruded aluminum
(6063-T5)
smoke damper frame is not less than 0.080”
(2.03 mm)
in
thickness. Damper frame is 4”
(101.6 mm)
deep x 1"
(25.4 mm)
, with mounting flanges on both
sides of frame. Damper frame has a 2"
(50.8 mm)
mounting flange on the rear of the damper,
when ordered as Extended Rear Flange install type.
2. Blades are maximum 6”
(152.4 mm)
deep extruded aluminum
(6063-T5)
air-foil profiles. All
blades are symmetrically pivoted.
3. Blade and frame seals are specially designed and engineered extruded silicone. Seals are
secured in an integral slot within the aluminum extrusions. Blade and frame seals are
mechanically fastened to prevent shrinkage and movement over the life of the damper.
4. Bearings are composed of a bronze oilite inner bearing - fixed around a
7
/
16
”
(11.11 mm)
aluminum hexagon blade pivot pin - rotating within a bronze oilite outer bearing inserted in
the frame.
5. The
7
/
16
”
(11.11 mm)
hexagonal drive rod, U-bolt fastener, and hexagonal retaining nuts are
zinc-plated steel. These provide a positive connection to blades and linkage.
6. Aluminum and corrosion-resistant zinc-plated steel linkage hardware is installed in the frame
side, complete with cup-point trunnion screws for a slip-proof grip.
7. Smoke dampers are designed for operation in temperatures ranging from -40°F
(-40°C)
to
250°F
(121°C)
.
8. Smoke dampers are custom made to required size, without blanking off free area.
9. Smoke dampers are available with parallel blade action.
CONSTRUCTION OPTIONS:
For each option listed, replace the lines above with their corresponding lines below.
MR - MOISTURE RESISTANCE OPTION:
1. Extruded aluminum
(6063-T5)
smoke damper frame is not less than 0.080”
(2.03 mm)
in
thickness. Damper frame is 4”
(101.6 mm)
deep x 1”
(25.4 mm)
, with mounting flanges on both
sides of frame. Damper frame has a 2”
(50.8 mm)
mounting flange on the rear of the damper,
when ordered as Extended Rear Flange install type. Frame is assembled using stainless steel
screws.
5. The
7
/
16
”
(11.11 mm)
hexagonal drive rod, U-bolt fastener, and hexagonal retaining nuts are
stainless steel. These provide a positive connection to blades and linkage.
6. Aluminum and stainless steel linkage hardware is installed in the frame side, complete with
cup-point trunnion screws for a slip-proof grip.
SW - SALT WATER RESISTANCE OPTION:
1. Extruded aluminum
(6063-T5)
smoke damper frame is not less than 0.080”
(2.03 mm)
in
thickness. Damper frame is 4”
(101.6 mm)
deep x 1”
(25.4 mm)
, with mounting flanges on both
sides of frame. Damper frame has a 2”
(50.8 mm)
mounting flange on the rear of the damper,
when ordered as Extended Rear Flange install type. Aluminum frame is clear anodized to a
minimum thickness of 0.7 mil
(18 microns)
deep. Frame is assembled using stainless steel screws.
2. Blades are maximum 6”
(152.4 mm)
deep extruded aluminum
(6063-T5)
air-foil profiles, clear
anodized to a minimum thickness of 0.7 mil
(18 microns)
deep. All blades are symmetrically pivoted.
5. The
7
/
16
”
(11.11 mm)
hexagonal drive rod, U-bolt fastener, and hexagonal retaining nuts are
stainless steel. These provide a positive connection to blades and linkage.
6. Linkage hardware is installed in the frame side. All aluminum linkage hardware parts are clear
anodized. All non-aluminum linkage hardware parts are stainless steel. They are complete with
cup-point trunnion screws for slip-proof grip.
SUBMITTAL DATA |
Series 1000 SM
UL/ULC Approved Smoke Damper
1
TAMCO JUNE, 2016
www.tamcodampers.com
© T.A. Morrison & Co. Inc., 2016
