3
GB
2
GB
GENERAL IDENTIFICATION
3
4
5
6
8
9
12
13
10
7
2
11
14
15
16
SAFETY FEATURES
13 MUFFLER SHIELD helps prevent hands, body and/or combustible materials from making contact with a hot muffler.
1.
LINEHEAD
2.
DEBRIS SHIELD
3.
DRIVE SHAFT ASSEMBLY
4.
HANDLE
5.
THROTTLE TRIGGER
6.
IGNITION SWITCH
7.
SAFETY TRIGGER LOCK
8.
CHOKE LEVER
9.
STARTER ROPE HOUSING
10. FUEL TANK
11. AIR FILTER COVER
12. STARTER HANDLE
13. MUFFLER SHIELD
14. PRIMER BULB
15. HARNESS
16. TOOL-LINK COUPLING
1
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Air-cooled, 2-Cycle, Chrome Cylinder
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25cc
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.8Kg
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450 ml
Drive Shaft Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142cm
Bump Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Twin Line
Cutting Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43cm
Cutting Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.5mm
Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .“J” Handle
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Electronic
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Centrifugal Clutch
Shaft Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Straight - Tool-Link
SPECIFICATIONS
• “J”
HANDLE
ASSEMBLY
1. To install handle onto unit, you will need the following
components from your user kit: “J” handle (A), fixing
holder (B), clamps (C) and screws (D). (Fig. 1)
2. Install the fixing holder (B) on the shaft around 4” (10-
12cm) away from the end of the grip, put the clamp
(C)over shaft and tighten the 2 screws (D).
3. Install the J handle (A) on the fixing holder, put the
other clamp (C) over J-handle and tighten the other 2
screws (D).
•
DRIVE SHAFT
Installing the lower shaft
1. Remove the cover from the lower shaft (A). Press the
release lever (B) while pushing the lower shaft into the
tool-link couping. (Fig. 2A)
2. Locate and lock the release lever into the primary hole
(C) in the shaft. (Fig. 2A)
3. Tighten the knob (D) securely clockwise before using
the unit. (Fig. 2B)
•
DEBRIS SHIELD & DEBRIS SHIELD SKIRT
1. Install debris shield and blade guard with 3 screws (A)
provided (Fig. 3A).
2. Turn the unit over and install the debris shield skirt (B).
Fig. 3B
• LINEHEAD
INSTALLATION
1. Install gear collar (C) ensuring that collar spacer (D) is
in place (Fig. 3C).
2. Insert holding pin (E) and thread linehead onto shaft.
Tighten linehead by hand only (Fig. 3D and 3E).
ASSEMBLY INSTRUCTIONS
Fig. 1
A
B
C
D
D
C
CAUTION: Make sure the release lever is
locked in the primary hole and knob is
securely tightened before operating this unit.
CAUTION: All attachments are designed to
be used in the primary hole unless otherwise
indicated in the specific attachment’s opera-
tor’s manual. If the incorrect hole is used, it
could result in injury, or damage to the unit.
B
A
Fig. 2A
Fig. 2B
C
D
Fig. 3A
Fig. 3B
A
B
