2
GB
GB
3
1.
Flare Nozzle
2.
Concentrator Nozzle
3.
Nozzle Lock Button
4.
Impeller Housing
5.
Drive Shaft
6.
Knob Spanner
GENERAL IDENTIFICATION
SPECIFICATIONS
Shaft Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7/8”
Dry Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.9 kg
4
5
3
1
2
6
•
INSTALLING SHAFT
1. Insert the drive shaft assembly (A) into the shaft
mount (B). Ensure that the shaft locks into place and
that the screw holes on the drive shaft and shaft
mount line up. Insert the silver (C) screw through the
shaft mount and into the drive shaft. (Fig. 1A)
2. To lock the shaft into place, slide the adjustable clamp
(D) over the drive shaft (E) and then onto the shaft
mount (B). (Fig. 1B) NOTE: Before sliding the
adjustable clamp over the drive shaft, ensure that the
dimples of the adjustable clamp are facing towards
the bottom. (Fig. 1C)
3. Position the adjustable clamp (D) on
the shaft mount (B) so that the middle dimple rests
above the silver screw (C) in the shaft mount. (Fig.
1D)
4. Insert the black screw (F) through the adjustable
clamp (D) and tighten with nut (G) using a spanner
and screwdriver (not supplied). (Fig. 1E)
•
DRIVE SHAFT
Installing the lower shaft on power head
1. Remove the cover from the lower shaft (A). Press the
release lever (B) while pushing the lower shaft into the
tool-link couping. (Fig. 2A)
2. Locate and lock the release lever into the primary hole
(C) in the shaft. (Fig. 2A)
3. Tighten the knob (D) securely clockwise before using
the unit. (Fig. 2B)
•
INSTALLING NOZZLE
Your unit comes with a flare nozzle and connector nozzle.
Use the following instructions to interchange the two noz-
zles.
To Change nozzle:
1. Press on the button on the top of the nozzle near the
connection, and pull the nozzle outward.
2. Insert another nozzle in place with the button in the
hole of the nozzle.
•
USING THE FLARE NOZZLE
Use the flare nozzle for large, hard surface areas such as
driveways and sidewalks. (See Fig. 3A)
•
USING THE CONCENTRATOR NOZZLE
Use the concentrator nozzle for hard to reach places such
as corners in a garage or to control dust in a dust laden
environment. (See Fig. 3B)
ASSEMBLY INSTRUCTIONS
B
Fig. 1A
Fig. 1B
A
D
E
C
Fig. 1C
C
Fig. 1D
Fig. 1E
B
D
G
F
D
CAUTION: Make sure the release lever is
locked in the primary hole and knob is
securely tightened before operating this unit.
CAUTION: All attachments are designed to
be used in the primary hole unless otherwise
indicated in the specific attachment’s opera-
tor’s manual. If the incorrect hole is used, it
could result in injury, or damage to the unit.
B
A
Fig. 2A
Fig. 2B
C
D
OPERATION INSTRUCTIONS
Fig. 3A
Fig. 3B
