background image

I

f the unit gives an error code, immediately switch the unit off. See error table below for proper corrective action. If the error cannot be cleared, please contact your Talboys 

representative for repairs.  

T

roUblesHooTing

 (H

oTPlaTe

 / H

oTPlaTe

-s

Tirrers

)

The stirring units do not have LED displays. In the event of a malfunction, the unit will beep 10 (ten) times. To clear the error, turn the control knob to the off position and cycle 

the power by disconnecting the power cord from the source. Reconnect power cord and resume operations. If the error persists, turn the unit off and contact your Talboys 

representative for repair. 

11

Error

Cause of Error

How to Fix

E1

An “E1” error means the heater sensor is open or malfunctioned. 

This error cannot be fixed by the end user. Please contact your Talboys representative 

for repair.

E2

An “E2” error means the heater sensor shorted or malfunctioned.

This error cannot be fixed by the end user. Please contact your Talboys representative 

for repair.

E3

An “E3” error means there is either no motion on the motor or the motor is 

not working properly.

Reset the unit by rotating the knobs for speed and heat to the off positions until 

they click then turn them back on. If it still doesn’t work, please contact you Talboys 

representative for repair.

E6

An “E6” error means there is an internal electronics system error. 

This error cannot be fixed by the end user. Please contact your Talboys representative 

for repair.

E8

An “E8” error means the unit had a catastrophic over temperature condition 

or temperature runaway condition (temperature greater than 600°C) and 

therefore automatically shut down to prevent damage.

This error cannot be fixed by the end user. Please contact your Talboys representative 

for repair.

E9

An “E9” error means the heater failed. This might occur if heater temperature 

fails to rise when asked to, or there is a sudden drop in heater temperature 

for no apparent reason.

This error cannot be fixed by the end user. Please contact your Talboys representative 

for repair.

T

roUblesHooTing

 (s

Tirrrers

)

Содержание Advanced 10 X 10

















Отзывы: