7
When the unit is mounted on unlebel wall,back
tamper switch could be kept turninig on. In this case,
use B.T.Killer which can disable the function ©.
7
WIRING
Terminal Confi guration
[COMMON BATTERY]
Common for TX-114TR/FR/SR and Transmitter
When connecting this unit to the transmitter
which has no input terminals for tampers, connect
alarm and tamper terminals of this unit in series.
Both alarm and tamper signals can be outputted.
(Select N.C. for contact output.)
SUPPLY VOLTAGE
•3 to 9VDC Alkaline or Lithium Battery (polarity)
•Current Consumption
(Except test-mode period)
25 μA (TX-114TR/114SR)
35 μA (TX-114FR)
• When a connected transmitter doesn’t accept the
output, to short curcuit between terminal of this
unit and the negative pole of the battery for the
transmitter may solve the problem.
ALARM
•Solid State Switch form N.O./N.C. selectable
•10VDC · 0.01A Max
[Detection Alarm]
OR
[Trouble Alarm]
TAMPER
•Solid State Switch form N.O./N.C. selectable
•10VDC · 0.01A Max
[Front Tamper]
OR
[Back Tamper]
[SEPARATE BATTERIES]
Each for TX-114TR/FR/SR and Transmitter
Powersupply needs same or higher voltage than
that for transmitter
When a connected transmitter doesn’t accept the
output, to connect the terminal of TX-114TR/
FR/SR and the negative pole of the battery for the
transmitter may solve the problem.
Wiring insertion
|
|
(1)
Put the wire through the wiring holes and connect
them to the battery and transmitter and the
terminals.
(2)
Fix the transmitter and battery on the back box
with the adhensive sheets.
* When connecting this unit to the transmitter which
has no input terminals for tampers, connect alarm
and tamper terminals of this unit in series.
Both alarm and tamper signals can be outputted.
(Select N.C. for contact output.)
8
INSTALLATION
Before the installation
|
|
Read
2
PRECAUTIONS
before the installation.
(1)
Loosen the cover locking screw.
(2)
Remove the cover.
(3)
Loosen the body locking screws.
(TX-114TR/114FR only)
(4)
Remove the body unit. (TX-114TR/114FR only)
Wall Mounting
|
|
TX-114TR/114FR
(1)
Break 2 knockouts on the mounting base.
(2)
Install the base to the wall with 2 tapping screws.
[Installed pitch: 3.29" (83.5mm)]
TX-114SR
(1)
Install the base to wall with 2 tapping screws.
[Installed pitch:8.25" (209.5mm)]
Pole Mounting
|
|
TX-114TR/114FR
Use the pole attachment "BP-32" (sold separately)
Use a 1.66" to 1.75" (38mm to 45mm) outer diameter
pole
(1)
Break 4 knockouts on the mounting base.
(2)
Attach 2 pole mounting brackets to the backside
of the base with 4 tapping screws.
(3)
Place the U brackets on the back of the pole.
Attach the mouting base to the U bracket with
pole mounting screws.
(4) Refer to
7
WIRING
and connect wires to the
terminals.
TX-114SR
Use the pole attachment "BP-22" (sold separately)
A
B
C
Assembling
|
|
(1)
Attatch the Body unit to the Mounting Base.
(TX-114TR/114FR only)
(2)
Fasten the Body locking screws.
(TX-114TR/114FR only)
* Carry out
OPERATION CHECK
with the cover
detatched.
(3)
Replace the cover.
(4)
Fasten the Cover locking screw.
OPERATION CHECK
•
Refer to the
3
DETECTION AREA
, and set the
horizontal angle and detection distance.
• Make functional settings in accordance with the
purpose of use of this unit.
SPECIFICATIONS
Model
TX-114SR
TX-114TR
TX-114FR
Detection system
Passive infrared
Coverage
When horizontal detection
Angle: 90°
Detection distance: 40' (12m)
Horizontal zone: 7zones
Downward zone: 7zones
2sets of
TX-114SR / TX-114TR
sensors
Coverage adjustment
Horizontal: 90 degrees
Detection distance: 6.6' to 40' (2m to 12m)
(Adjustable by changing the vertical angle of downward curtain)
Supply voltage
3V to 9VDC Alkaline or Lithium Battery
Operation voltage
2.3V to 10VDC (Battery)
Current consumption
25
μ
A for detection
35
μ
A for detection
5mA/3V (Test mode)
Operation
Solid State Switch N.C./N.O. selectable
10VDC · 0.01A Max
z
Alarm output
|
|
One shot output when detecting human beings (approx. 2sec)
z
Tamper output
|
|
Real time output
•
when the cover is detatched from the unit
•
when the unit is detatched from the installed wall or pole. (TX-114TR/TX-114FR Only)
z
Trouble output
|
|
Real time output when the unit suffers functional trouble. (from terminal of Alarm)
Operation LED
Red LED
•
Blinking for approx. 1min at warming-up
•
Lighting for 1sec at detection during walk-test (LED lights only in a test-mode)
•
Blinking when trouble alarm is issued (Lights once every 5 sec)
Sensitivity adjustment
Approx. 30% to 170% (By volume)
Pulse count
1/3 selectable with a dip switch
Alarm prohibition time
10sec/120sec/300sec/900sec selectable with dip switches
Detection mode
AND/OR selectable
Ambient temperature
-4°F to +122°F (-20°C to +50°C)
Mounting position
Indoor/Outdoor [Wall or Pole]
Weight
14oz (400g)
19.6oz (560g)
21.7oz (620g)
Appearance
Body: AES resin Lens: PE resin
TROUBLESHOOTING
Trouble
Check
Corrective Action
Completely inactive
•
Battery is unconnected or low battery.
•
Connect battery or replace battery.
•
Cover is shielded by substances (including
glass).
•
Remove the substances.
•
Improper area adjustment.
•
Readjust the protection area setting.
•
Not yet about 1minute after a battery is connected
to the unit. (Operation LED is
fl
ickering.)
•
Allow for warming up time (about 1min.)
•
The voltage of powersupply is lower than that
for transmitter.
•
Use same or higher voltage than transmitter.
•
Incorrect polarity of powersupply
•
Change the polarity.
•
Improper setting of output form
•
Select the correct setting.
Sometimes inactive
•
Improper area adjustment.
•
Readjust the protection area setting.
•
Cover face is soiled with dust or water drop.
•
Clean the cover with soft cloth.
•
Detection occurs within the signal prohibition
time set by a dip switch.
•
If the sensor sends a signal after the
prohibition time is over, its function is normal.
Activated when no person
has passed
•
Something moving in protected area or too
rapid temperature variations.
•
Remove the cause.
•
Large electrical noise source such as power
machine nearby or its wiring close to that of
sensor.
•
Relocate device.
•
Intense re
fl
ection of sun light or head light
shining on the sensor.
•
Relocate device. Readjust the protection area
setting.
•
Re
fl
ective lights such as sun light or head
light affect the downward zone.
•
Remove re
fl
ective objects.
•
Readjust the protection area setting.
•
Improper installation of the sensor.
•
Install the sensor vertically.
•
Detection distance of the downward zone is too long.
•
Readjust detection distance.
•
Cars or motor bikes located at the front of
detection area may activate the sensor.
•
Readjust the area setting and range adjustment
so that there is no such undesirable detections.
LED lights on once every
5 min though the unit is
not in a test mode
•
The unit suffers functional trouble. (Trouble
signal is issued.)
•
Check the function of the sensor.
Solve possible problems according to the following table. If normal operations cannot be
restored by this means, contact either the dealer from whom you bought the unit or TAKEX.
• Connect the battery to the unit after which approx.
1 min warm up period starts.
• Attach the cover to the unit and fi x it by tightening
the cover locking screw.
(After the warm up time is over and the cover is
attached to the sensor, the unit will be in a test mode
for about 5 min.)
• After the warm up time is over, operate a walk test
and check the location and size of the detection area
through the LED.
• If necessary, readjust the angle and distance of
the detection area as well as sensitivity and pulse
count.
* Make sure that there is no undesirable detection of
traffi c including vehicles if there is a path or road at
the front of detection zone.
Limited Warranty:
TAKEX products are warranted to be free from
defects in material and workmanship for 12 months
from original date of shipment. Our warranty does
not cover damage or failure caused by Acts of God
(including inductive surge by lightning), abuse,
misuse, abnormal usage, faulty installation, improper
maintenance or any repairs other than those
provided by TAKEX. All implied warranties with
respect to TAKEX, including implied warranties for
merchantability and implied warranties for fi tness,
are limited in duration to 12 months from original date
of shipment. During the Warranty Period, TAKEX
will repair or replace, at its sole option, free of charge,
any defective parts returned prepaid. Please provide
the model number of the products, original date of
shipment and nature of diffi culty being experienced.
There will be charges rendered for product repairs
made after our Warranty period has expired.
