Takagi T-H3J-DV Скачать руководство пользователя страница 42

Страница: 42 / 80

SER

VICE PR

OCEDURE

SER
VICE PR

OCEDURE

SER

VICE PR

OCEDURE

SER
VICE PR

OCEDURE

42 • On-Demand Water Heater Service Handbook for 240, 340 & 540 Condensing Models

9.2 Insert an air compressor’s air

hose into the opening from

which the burner was removed.

◦

Blow air up into the heat

exchanger to remove

soot and debris.

◦

At the same time,

vacuum the combustion

chamber with a shop vac.

◦

Continue until all dirt has

been removed.

10.

Clean the parts of the flame rod and

air/fuel ratio rod (AFR) that are on the

inside of the burner. (Use sand paper

or other appropriate abrasive.) See

“Cleaning the Rod Assembly (Flame

Sensor and Air/ Fuel Ratio Rod),”

page 36.

NOTICE: Do not clean the metal

extensions on the outside of the

burner. See Figure 33.

11. Reassemble all items in reverse order.

WARNING!

Ensure that you reinstall

the brass-colored screw that

secures the gas valve to the gas inlet

connection. Failure to do so can lead

to a gas leak which can result in severe

personal injury or death.

Things to remember:

•

Reinstall the solenoid connectors

to the gas valve before you

reinstall the gas valve/manifold

plate assembly. See Figure 34.

•

Only four solenoid circuits have

numbers labeled on their wires: 3, 9,

53, and 73. (See Figure 34. See also

schematics on pages 30 or 31.)

•

The connector which connects to the

gas proportional valve is not labeled

with a number. It has two wires: red

and white. (See schematics on pages

30 or 31.)

NOTICE:

□

If necessary, refer to the

exploded assembly views

which start on page 71.

□

Inspect all gaskets.

□

Ensure that the black O-rings

and mesh filter on the gas

valve inlet are not pinched or

otherwise damaged during

reinstallation.

□

ALL screws must be hand

tightened only, especially

around the gas valve inlet.

□

Reconnect the plastic tube

that runs from the gas

valve to the bottom of the

combustion chamber.

□

Reinstall the fan.

□

Reinstall the igniter assembly.

□

Verify that all components are

reattached and are secure.

□

Ensure that all wire

connectors have been

reconnected.

Flame Rod /AFR

Assembly

Front of burner:

• Do not clean the extensions

on the outside (shown above).

• Clean the metal extensions on

the inside of the burner.

Figure 33.

Solenoid

(locations vary)

Connector

Numbered

Wire

Stamped

Number

In each case, these numbers

must match.

Connectors have no polarity.

Figure 34.

□

Ensure that the solenoid

connectors are reinstalled in

the correct locations.

To do so, match the printed

number on the wire to the

corresponding number that

is stamped on the solenoid

body.

See Figure 34.

For example, if “73“ is printed

on a wire, its pin should plug

into the side of the connector

that has the number “73”

stamped closest to it.

□

All connectors with

yellow

wire

go to the same circuit. They

may be reconnected in any

order.

Содержание T-H3J-DV
















































































Результаты поиска

Содержание T-H3J-DV

Отзывы:

Бренды по названию

Популярные бренды

Takagi T-H3J-DV, Руководство по обслуживанию

Результаты поиска

Содержание T-H3J-DV

Отзывы:

Бренды по названию

Популярные бренды