manualshive.com logo in svg

Takagi GS-2000W-AU, Руководство по установке

Поделиться
Скачать
Takagi GS-2000W-AU Скачать руководство пользователя страница 23

23

 WATER HEATER

PROBLEM

POSSIBLE SOLUTIONS

Unit does not ignite when water 

goes through the unit.

•  Is the flow rate over 3.0 l/min? (p. 18)
•  Check for the filter on cold water inlet. (p. 21)
•  Check for reverse connection and cross connection.
•  If you use the remote controller, is the power button turned on? 

(p. 18,19)

The fan motor is still spinning after 

operation has stopped.

•  This is normal. After operation has stopped, the fan motor keeps 

running for 15 to 75 seconds in order to re-ignite quickly, as well as 

push all exhaust gas out of the flue. 

REMOTE CONTROLLER (OPTIONAL)

PROBLEM

POSSIBLE SOLUTIONS

Remote controller does not display 

anything when the power button is 

turned on.

Press the ON/OFF button.
If the lamp does not light:

•  Make sure the unit has power supply.
•  Make sure the connection to the unit is correct.(p. 16)

An ERROR code is displayed.

Please see the p.24

Remote controller can not change 

the set temperature.

Is priority lamp lit?

If it is not, press the priority button after closing all hot water taps.

Содержание GS-2000W-AU





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды