manualshive.com logo in svg

Tait TM8100 mobiles, Руководство по протоколу

Поделиться
Скачать
Tait TM8100 mobiles Скачать руководство пользователя страница 11

 

TM8100/TM8200 Computer-Controlled Data Interface (CCDI) Protocol Manual

CCDI

11

© Tait Electronics Limited

 

April 2007

1

CCDI

The Computer Controlled Data Interface (CCDI) protocol is a Tait 
proprietary command protocol embedded in the TM8100 and TM8200 
radios, and used for communicating with the radio via asynchronous serial 
ports and over-air.

The radio is the DCE and is connected directly to the DTE, usually a PC, 
via the serial port.

Two modes of operation are available:

■

Command mode

■

Transparent mode

When in Command mode, commands and response messages are passed 
between the PC and the radio using the CCDI protocol. CCDI commands 
can also be used to obtain GPS data and NMEA messages from the radio. 
Refer to 

“QUERY”

 and 

“SEND_ADAPTABLE_SDM”

. The baud rate is 

set to 1200, 2400, 4800, 9600, 14400, 19200, 28800 or 115200 (TM8200 
only) baud, using the programming application.

When in Transparent mode, communication between the PC and the radio 
is set to 1200, 2400, 4800, 9600, 14400, 19200, 28800 or 115200 (TM8200 
only) baud, using the programming application.

The over-air data rate is 1200 or 2400 bit/s for FFSK data,
12 kbit/s for Tait High Speed Data (THSD) narrow band and wide band, 
and can be set to 19200 bit/s for THSD wide band.

Figure 1.1

Modes of operation

PC Serial Port

PC running

terminal application

PC running

terminal application

PC Serial Port

Содержание TM8100 mobiles













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды