Tait TM8100 mobiles Скачать руководство пользователя страница 30

Страница: 30 / 76

CCDI

TM8100/TM8200 Computer-Controlled Data Interface (CCDI) Protocol Manual

April 2007

1.9.5

QUERY

The QUERY command requests information from the radio.

Format

q [SIZE] [QUERY_TYPE] [DATA] [CHECKSUM]

■

‘q’ is sent as a single ASCII character and represents the QUERY
command.

■

[QUERY_TYPE] is a single ASCII character representing the query
type required.

■

[DATA] is a number with up to three-digits which identifies the CCTM
command which is sent.

Note

If no [QUERY_TYPE] is sent, then the QUERY command will
default to [QUERY_TYPE] = 0.

[QUERY_TYPE] [DATA]

Function

Support

0
(model and CCDI
version)

none

Query the radio model and CCDI version. Data is returned
as a MODEL message.

Yes

1
(query SDM)

none

The buffered SDM data is returned to the PC as a
GET_SDM message. The SDM buffer is then cleared.
Available in conventional mode only.

Yes

3
(version)

none

Query the radio version information. The data is returned
to the PC as a RADIO_VERSION message. Refer to

“RADIO_VERSIONS”

Yes

4
(serial number)

none

Query the serial number. Refer to

“RADIO_SERIAL”

Yes

5
(CCTM)

047

PA temperature. Returned to the PC as a
CCTM_QUERY_RESULT message. Refer to

“CCTM_QUERY_RESULTS”

TM8100: from v2.10
TM8200: No

063

Averaged RSSI level. Returned to the PC as a
CCTM_QUERY_RESULT message.

TM8100: from v2.09
TM8200: No

064

Raw RSSI level. Returned to the PC as a
CCTM_QUERY_RESULT message.

318

Forward power. Returned to the PC as a
CCTM_QUERY_RESULT message.

319

Reverse power. Returned to the PC as a
CCTM_QUERY_RESULT message.

6
(GPS)

none

Query GPS. GPS data is returned packetised as though the
TM8100/TM8200 is a polling radio.

TM8100: from v2.10
TM8200: No

7
(display)

Returns the text of the entire display. Non-ASCII text is
ignored.

TM8100: No
TM8200: from v3.03

Содержание TM8100 mobiles













































































Результаты поиска

Содержание TM8100 mobiles

Отзывы:

Бренды по названию

Популярные бренды

Tait TM8100 mobiles, Руководство по протоколу

Результаты поиска

Содержание TM8100 mobiles

Отзывы:

Бренды по названию

Популярные бренды