Tait TA2922 Скачать руководство пользователя страница 4

Страница: 4 / 8

TA2922 TM8/TM9 Universal Line Interface Board Installation Instructions

Fit other additional solder links if required.
Other available configuration solder links are:

■

2/6/8-wire operation

■

keying options

■

gate out relay operation

■

software profile configurations.

These bottom-side solder link pads can alternatively be fitted with top side machine-
populated 0603 resistors. The table below indicates the hardware variants and the rela-
tionship between bottom side solder link pads and top side resistor locations. Note that
some solder link pads are 2-way while others are 3-way links.

To fit the board, refer to the following diagram for item numbering. Remove the top
cover and lid

from the radio to access the options cavity.

Remove the external options connector bung

, if it is fitted.

On the inside of the radio lid place the foam seal

over the external options connec-

tor cavity

With the top side of the universal line interface board

facing the radio lid, guide the

external options connector

into the external options connector cavity.

Screw the external options connector to the radio lid using the two screw-lock fasten-
ers

Tighten the fasteners

to a torque of 0.9N·m (8lbf·in).

Important:

The external options connector screw-lock fasteners must be tightened

correctly before screwing the universal line interface board onto the mounting posts

Solder link

SMD resistor

Description

LK1 1-2

R46

Connect normally open relay contact to /GATE OUT 1

LK1 2-3

R78

Connect normally closed relay contact to /GATE OUT 1

LK4

R62

Enable RX line audio from line TX pair (2-wire line operation)

LK5 1-2

R82

Connect 2-wire line transformer centre tap to RX gate relay output

LK5 2-3

R80

Connect 2-wire line transformer centre tap to optocoupler input

LK6 1-2

R77

Connect normally open relay contact to /PTT IN 1

LK6 2-3

R76

Connect normally closed relay contact to /PTT IN 1

LK7

R65

C13.8V to relay common and /GATE OUT 2

LK8

R81

Connect half of optocoupler input and /PTT IN 2 to DC ground

LK9

R42

Select configuration profile 2 (if enabled in programming)

Содержание TA2922









Результаты поиска

Содержание TA2922

Отзывы:

Похожие инструкции для TA2922

Бренды по названию

Популярные бренды

Tait TA2922, Руководство по установке

Результаты поиска

Содержание TA2922

Отзывы:

Похожие инструкции для TA2922

Бренды по названию

Популярные бренды