Taiden HCS-4345NTK Скачать руководство пользователя страница 11

 

  5

 
 
 
 
 
 
 

 

Note: 

)

  The IC card should be keep 50 cm - 160cm 

high from the ground; 

)

  The IC card should NOT be kept parallel to 

the ground; 

)

  The IC card should NOT be fully placed 

together with metal items, such as key, 
cigarette case, mobile phone, mobile hard 
disk, etc. 

)

  The IC card should NOT be placed together 

with monthly ticket, membership card, 
identification card, etc. 

)

  The IC card should be protected by hard card 

jacket and avoid buckling, otherwise it may 
shorten detection distance or even detection 
failure. 

)

  Sign-in machine should be placed far from 

large metal objects and reinforced concrete 
wall; 

)

  Sign-in machine is a RF device, and may be 

jammed by other RF devices with similar 
frequency or low frequency and high power. 
Therefore, it should be kept away from 
interfering resources. 

)

 When direction judgement function is 

enabled, to ensure the accuracy of direction 
judgement, two persons pass through the 
passage in opposite direction or side-by-side 
should be avoided. When several persons 
pass through the passage one by one, they 
should keep a space larger than 30 cm. 

Содержание HCS-4345NTK




















Отзывы: