background image

26

|

care and maintenance

There is a fuse in the
power socket on the
back of your 250MR. To
change the fuse, unplug
the power cable and
carefully pull out the fuse
carrier drawer

(1)

.The fuse carrier contains a

spare fuse; this is the first one that you see
when you open the carrier. 

There are no other user-serviceable parts
inside the 250MR.

In order to maintain the appearance of
your 250MR, you can clean it as follows:

• before cleaning always disconnect

your 250MR from the AC supply;

• any grease or dirt on the case may be

removed with a soft, lint free dry cloth.
Do not use any other solutions. Do not
use water or any solvents or abrasives;

• take great care not to get any liquid

inside the case. If this happens, you
should have your 250MR serviced.

fuses

ser vice

cleaning

The only routine service you should do to your 250MR is described on the previous page. All
other servicing should only be carried out by one of our authorised service agents.

If service is required, please contact your authorised TAG McLaren Audio retailer. If your
250MR is still under guarantee, please refer to the guarantee card which gives you details
on how to claim against the guarantee.

Please keep the original packaging and use it whenever your 250MR is transported.

1. You cannot open the fuse drawer while the plug is in the socket

GRR00794.03-UK 250MR  5/4/02  11:50 am  Page 26

Содержание 250MR

















Отзывы: