tae TA-100/6P Скачать руководство пользователя страница 6

6

missprints and technical changes reserved

Instruction & Operating Manual

TA-15/6P...200/6P

11)

Current limit: In order to check the current limit the field must be disconnected, the motor must be

blocked and the field control (jumper 

XI

) must be jumpered. Switch on drive and preselect speed

and adjust the requested current with P5 (current limit). The red LED 6 (current limit) must light up.

This adjustment should be performed with in 10 sec., otherwise the blocking control will become

effective. If the adjustment takes longer than 10 sec. and the bolcking control is actuated, press the

key TA to confirm the blocking. The drive will then immidiately operate at the current limit.

12)

Zero-speed control: If a controlled deceleration after normal switch-off (provided the machine

operates with positive torque) is required, jumper 

VI

 must be installed to make the zero speed

control operative. (zero speed control is effective above approximately 10% of the speed.)

13)

Stability potentiometer P8. This potentiometer must be adjusted so that the drive operates without

overshoot in the presset speeds.

5.2 Tachometer feedback control:

1)

Check all connections with an Ohm-meter for grounds

2)

Install required jumpers for tachometer feedback control (depending if a.c. or d.c. tachometer is

used (see page 2) terminals 19 and 20 or 11 and 20 respectively.

3)

Remove resistor R82 and also remove jumpers 

VII

 and 

I

 . The electronic circuit is now without any

potential.

4)

For all further adjustments refer to the adjustments as previously described for the armature

feedback control, however, 

I x R compensation (P3) must be set fully counter clockwise.

6.

Troubleshooting

For fast and effective troubleshooting and for the location of defective components proceed as follows.
Check the drive for:
a) Intermittent or loose connections
b) Defective insulation of the connection leads
c) Defective motor (brushes etc.)

Caution!

Do not use 

any

 Mega-Ohm-meter, buzzer or similar test instruments.

Test instruments must be galvanically seperated from a.c. line. The electronic circuit

carries a voltage potential against ground when the drive is armature feedback

controlled (UA-controlled).

Содержание TA-100/6P











Отзывы: