Tadiran Telecom TGW4 SERIES Скачать руководство пользователя страница 139

Страница: 139 / 142

TGW4/8 Gateway Series for Aeonix High Availability Configuration Guide

Tadiran Telecom (TTL) L.P.

127

6.4.2 Set SIP Servers

Step0

If a domain name was entered in the

Registrar server

field (

Step3 above),

skip to

Configuring the Domain Name of the Primary Server

, on next page.

Configuring the IP Address of secondary SIP Servers

A maximum of five secondary servers can be added

To configure the IP addresses of the secondary SIP servers:

Step1

Click

Add

Step2

In the

SIP server n

field enter the IP address of the secondary Aeonix server.

Step3

Repeat Step1 and Step2 for the next server, up to five secondary servers.

Figure 6-30

Page to set additional servers

Step4

Click

Save

Step5

Skip to

Configure OPTIONS and REGISTER Settings

on page 129.

Содержание TGW4 SERIES















































































































































Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды

Tadiran Telecom TGW4 SERIES, Руководство по настройке пользователя

Результаты поиска

Содержание TGW4 SERIES

Отзывы:

Бренды по названию

Популярные бренды