WARNING AND OPERATING INSTRUCTIONS
FOR ON RUBBER LIFTING CAPACITIES
1.Rated lifting capacities on rubber are in pounds and do not exceed
6 Over front operation shall be performed within two degrees in front of
75 % of tipping loads as determined by SAE J765-Crane Stability
chassis.
Test Code.
7 On rubber lifting with "jib" is not permitted. Maximum permissible
2.Rated lifting capacities shown in the chart are based on condition
boom length is 96.8 ft. (29.5m).
that crane is set on firm level surfaces with axle oscillation lockout
8 When making lift on rubber stationary, set parking brake.
applied. Those above bold lines are based on tire capacity and
9 For creep operation, boom must be centered over front of machine,
those below, on crane stability. They are based on actual load
swing lock engaged, and load restrained from swinging. Travel slowly
radius increased by tire deformation and boom deflection.
and keep the lifted load as close to the ground as possible, and
3.If the axle oscillation lockout cylinders contain air, the axle will not
especially avoid any abrupt steering, accelerating or braking.
be locked completely and rated lifting capacities may not be
10 Do not operate the crane while carrying the load.
obtainable. Bleed the cylinders according to the operation safety
11 Creep is motion for crane not to travel more than 200 ft. (60 m) in any
and maintenance manual.
30 minute period and to travel at the speed of less than 1 mph
4.Rated lifting capacities are based on proper tire inflation, capacity
(1.6km/h).
and condition. Damaged tires are hazardous to safe operation of
12 For creep operation, set Drive select switch to "4-WHEEL (Lo)" and
crane.
set gear shift lever to "1".
5.Tires shall be inflated to correct air pressure.
Air Pressure
57 psi (4.0 kgf/cm2)
WARNING AND OPERATING INSTRUCTIONS
FOR USING THE LOAD MOMENT INDICATOR (AML-C)
1. When operating crane on outriggers:
When a load is lifted in the front position and then swung
Set P.T.O. switch to "ON".
to the side area, make sure the value of the LOAD
Press the outrigger mode select key to register for the
MOMENT INDICATOR(AML-C) is below the 360
o
lifting
outrigger operation. Press the register key, then the outrigger
capacity.
mode indicative symbol changes from flashing to a solid light.
(2) For creep operation.
Press the lift mode select key to select the lift status that
The creep capacities are attainable only when boom is
corresponds to the actual boom configuration.
in the straight forward position of chassis and the over
Each time the lift mode select key is pressed, the ststus changes.
front position symbol is on. If boom is not in the straight
Press the register key to register the lift status, then the lift
forward position of chassis , never lift load.
indicative symbol changes from flashing to a solid light.
3. A swing does not automatically stop even if the crane
when mounting and stowing jib, select the jib set status.
becomes overloaded.
(the jib state indicative symbol will be flashing.)
4. During crane operation, make sure that the displays on front
2. When operating crane on rubber:
panel are in accordance with actual operating conditions.
Set P.T.O. switch to "ON".
5. The displayed values of LOAD MOMENT INDICATOR
Press the outrigger mode select key. The on-tire mode
(AML-C) are based on freely suspended loads and make no
indicative symbol comes on. Each time the outrigger mode
allowance for such factors as the effect of wind, sudden
select key is pressed the status changes. Select the creep
stopping of loads, supporting surface conditions, inflation of
operation, the on-tire mode indicative symbol flicker.
tire, operating speed, side loads, etc.
Press the lift mode select key to register the boom or single top
For safe operation, it is recommended when extending and
lift.
lowering boom or swinging, lifting loads shall be
However, pay attention to the following.
appropriately reduced.
(1) For stationary operation.
6. LOAD MOMENT INDICATOR (AML-C) is intended as an aid
The front capacities are attainable only when the over front
to the operator. Under no condition should it be relied upon
position symbol comes on. When the boom is more than
to replace use of capacity charts and operating instruction.
2 degrees from centered over front of chassis, 360
o
Sole reliance upon LOAD MOMENT INDICATOR (AML-C)
capacities are in effect.
aids in place of good operating practice can cause an
accident. The operator must exercise caution to assure
safety.
TR-1000XL Axle weight distribution chart
Base machine
Remove: 1.
6.6metric ton hook ball
-462
138
-147
-209
62
2.
100t hook block
-3,660
1,764
-860
-1,660
800
3.
Top jib
-964
245
-326
-437
111
4.
Base jib
-3,706
1,821
-855
-1,681
826
5.
Auxiliary lifting sheave
-325
216
-49
-147
98
6.
Removable Counterweihgt
9,202
-30,862
-9,825
4,174
-13,999
(with Auxiliary Hoist&wire)
52,275
25,990
26,285
-21,660
Rear
-324
-1,896
-1,885
115,245
57,298
57,948
Kilograms
GVW
Front
Rear
Tires
29.5-25 34PR
-109
Pounds
GVW
Front
-719
16
Содержание GR-1000XL-2
Страница 5: ...GR 1000XL WORKING RANGE CHART 5...
Страница 6: ...GR 1000XL WORKING RANGE CHART 6...
