FASTENING TOOLS
FOR THE PROFESSIONAL
7
6
•
Never point any power tool at yourself or at any other
person.
While working, hold the tool in such a way that no
injuries can be caused to the head or to the body in the event of
possible recoil.
•
Do not drive fasteners on top of other fasteners.
•
Do not use this tool to fasten electric cables.
This tool is not
designed for the installation of electric cabling and may damage
electric cables which could lead to injury by electric shock or
fire hazards.
Features
(Fig. A)
1. Firing Mode Selector
2. Trigger
3. Quick Release Plug (Euro Fitting)
4. Magazine Drum
5. Depth Adjustment Wheel
6. Magazine Release Latch
7. Air Deflector
Set up
Your air tool is fully assembled when you receive it. Before using it,
attach the air line and desired air system accessories. See Fig. B for
the recommended accessories and connection order. Be sure the
air hose is de-pressurised when installing or removing adaptors to
the air line.
Connecting The Tool to an Air Supply
(Fig. B)
• Determine if the tool needs oil and, if necessary, place two
drops of oil in the air plug as shown in Fig. B. If you are using an
automatic in-line oiler, check and add oil if necessary.
• Turn the compressor on and set the regulator to the proper
pressure for the size and type of fastener being used.
• Connect the tool to the air supply.
Loading the Tool
(Fig. C)
• Squeeze latch to open nail door, then rotate magazine door so it
is fully open.
NOTE:
THE MAGAZINE PLATFORM MUST BE SET FOR THE LENGTH
OF NAIL TO BE USED. NAILS WILL NOT FEED SMOOTHLY IF THE
PLATFORM IS NOT CORRECTLY ADJUSTED.
• The magazine contains an adjustable nail platform on which the
nail coil rest. The nail platform can be moved up and down across
various settings. To change nail platform height, pull up and twist
post until correct height is met (3).
• Place the coil of nails over the post of the platform in the magazine.
• Uncoil enough nails to reach the nose of the tool.
• Insert the first nail into the nose and the second nail between the
two rails of the feed pawl.
NOTE:
Be careful not to deform the coil of nails during the loading
process. Otherwise, the nail guide door will not close and the nails
might not feed consistently.
• First close magazine cover, then close latch door. Make sure the
door latch is completely engaged (6).
Adjusting the Depth
(Fig. D)
The driving depth of the fasteners can be set with the depth
adjustment wheel (5).
•
Fasteners are not driven in deep enough:
To increase the
driving depth, turn depth adjustment wheel to the left.
or
•
Fasteners are driven in too deeply:
To reduce the driving
depth, turn the depth adjustment wheel to the right.
•
Test the new driving depth on a test workpiece. Repeat steps
above as required.
Operating the Tool
Test the driving depth in a sample piece of wood before using. See
section ADJUSTING THE DEPTH.
• Connect the tool to the air supply. Make sure the air pressure is
in correct range denoted in section of TECHNICAL DATA.
• Load fasteners as directed in the section called LOADING THE
FASTENERS.
• Hold the body and press the drive guide to work surface, be sure
the tool is straight and then gently depress the trigger to drive
the fastener.
• Lift the tool off the work surface.
Firing Modes
(Fig. E)
The tool has two driving modes:
Sequential fire:
• Choose the correct mode before firing by rotating the FIRING
MODE SELECTOR SWITCH (Fig. E).
• Put the nose on the working surface, lightly push the tool toward
the working surface until the safety bracket is depressed, then,
depress the trigger to drive the fasteners. Whilst maintaining
contact with the working surface, the tool will drive a fastener
each time the trigger is depressed.
Contact trip (Bump fire):
• Choose the correct mode before firing by rotating the FIRING
MODE SELECTOR SWITCH (Fig.E).
• First, depress the trigger, then, repeatedly impact the safety
bracket, the tool can repeatedly drive the fasteners.
The tool will drive one fastener when the safety bracket is
impacted once.
NOTE:
The air deflector (Fig. F) is directional and can be rotated
through 360°.
Removing a Jammed Fastener
NOTE:
You must remove any jammed fasteners before using the tool
any further. If you continue to try and fire a fastener while the tool is
jammed, you could cause damage to the mechanism.
• Disconnect tool from the compressed air system
• Remove any unused fasteners from the magazine, this should clear
the jammed fastener(s).
• If any fasteners remain stuck in the nose piece, place tool upside
down on a solid surface. Put a punch or small screwdriver into the
firing nozzle and carefully tap to release the jammed fastener.
•
Close the nose plate and lock the latch before reconnecting to the
air system.
• Following the removal of a jammed fastener, always carefully test
the tool function before proceeding with any work. If fasteners
become jammed in the nose piece frequently, have the tool serviced
by a Tacwise Engineer or appointed service agent.
FASTENING TOOLS
FOR THE PROFESSIONAL
EN
65mm Coil Nailer HCN65P
Congratulations!
On the purchase of your Tacwise power tool. Your tool will perform
to your satisfaction for a long time if handled in accordance with our
Safety and Operating instructions.
Save this manual for future reference
Technical Data
Characteristic
Value
Minimum operating air pressure 70psi
Maximum operating air pressure 120psi
Nail length range
32mm (1 1/4") - 65mm (2 9/16")
Nail size
2.3-2.9 Flat Coil
Magazine capacity
300
Air inlet
1/4" NPT
Air consumption
3.2 CFM @ 90psi
Weight
2.5kgs (5.5lbs)
Vibration emission level*
2.9m/s
2
* The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase
exposure level over the total working period.
CE – Declaration of Conformity
65mm Coil Nailer HCN65P
Tacwise declares that this power tool has been designed in
compliance with the Regulations and Standards of the
European Directives.
Quality Department, Tacwise Group Plc – UK
WARNING! Before Use Carefully Read And Understand
All Instructions.
Failure to do so could result in fire and/or serious personal injury.
For any queries relating to safety matters on this power tool, please
email
.
Unpacking
• Carefully remove the tool and accessories from the box.
• Inspect the tool carefully to make sure no breakage or damage
occurred during transit.
• If any parts are damaged or missing, please email
for assistance. Do not operate this tool
until the missing or damaged parts are replaced. Failure to do so
could result in a personal injury.
• Whilst every effort has been made to ensure accuracy of
information contained within this manual, the Tacwise policy is
one of continuous improvement to our products and as such
we reserve the right to change the product specification without
prior notice.
General Safety Instructions
Important.
Tacwise recommends that this power tool should not
be modified or used for any application other than that for which
it was designed. Any such alteration or modification is misuse and
could result in a hazardous condition leading to a personal injury. If
you are unsure of its relative applications do not hesitate to contact
us and we will advise you.
Work Area
•
Keep your work area clean and well lit.
Cluttered benches and
dark areas invite accidents.
•
Keep children and pets away.
All visitors should be kept a safe
distance from work area.
•
Secure work.
Use clamps or a vice to hold work. This frees both
hands to operate the power tool.
Safety Warnings & Cautions
•
Never use oxygen combustible gases, bottled gases or high
pressure compressed gas as a power source for this tool.
The tool may explode and cause serious injury.
•
Outdoor extension cords.
When air compressor is used
outdoors, use only rounded jacket extension cords intended for
outside use. See manufacturer’s manual for the AWG required for
the compressor’s amperage draw.
•
Pay attention to air hose and their connections.
Don’t trip over
hoses. Make sure all connections are tight.
•
Use the correct air connector.
The connector on the tool must
not hold pressure when the air supply is disconnected. If the
wrong fitting is used, the tool can be charged with air after being
disconnected and still be able to drive a fastener.
•
When connecting the air.
The tool may possibly fire the
fasteners as soon as you plug it in to the air hose. Therefore,
remove all the fasteners before connecting to the air.
• Do not depress the trigger when loading.
•
If the fasteners are jammed.
Disconnect the tool from the air
and remove the jammed fasteners.
•
Stay alert.
Always watch what you are doing and use common
sense. Do not operate a power tool when you are tired or under
the influence of medication, alcohol or drugs.
•
Wear proper clothing.
Do not wear loose clothing or
jewellery that can catch in moving parts. Non-slip footwear is
recommended. Contain long hair and roll long sleeves above
the elbow.
•
Do not over reach or use on unstable surfaces.
Keep proper
footing and balance at all times.
•
Use safety equipment.
Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate
conditions. Wear CE approved safety goggles at all times. Normal
spectacles only have impact resistant lenses; they are NOT safety
glasses.
•
DO NOT use on hard surfaces
such as rock, concrete, masonry,
bricks or steel. Personal injury or damage to the power tool
could result.
•
Stored power tools.
When not in use, all power tools should be
stored in a dry, locked cupboard, out of the reach of children and
other untrained persons.
•
Recommended accessories.
Use only accessories that are
recommended by the manufacturer for your model. Accessories
that may be suitable for one tool may create a risk of injury when
used on another tool.
•
Beware of hidden danger.
Always make sure there is no danger
of hitting any hidden power cables, water or gas pipes.
•
Always assume that the tool is loaded with fasteners.
Handling the tool without care could result in an unexpected
firing of fasteners and lead to personal injury.
•
Do not activate the power tool unless it is in contact with the
work piece.
Serious injury can result if you depress the
safety lock pin on nose/contact trip with your fingers, or by
improper operation.
