background image

iWorx® ZXU1

502-007, Effective: May 30, 2013

15 

© 2013 Taco Electronic Solutions, Inc.

6.Press 

Reset Settings Heat

.

7.The 

Reset Settings Heat

 menu opens.

a.Specify Water 

Reset Low

 in degrees.

b.Specify Water 

Reset High

 in degrees.

c. Specify 

Boiler Pro

tection in Degrees (Lowest 

Return Water Temperature to return to the Boiler).

d.Press 

Save

.

8.Press 

Valve (or Variable Speed Circ) Settings

.

9.The 

Valve (or Variable Speed Circ) 

menu opens.

a.Specify 

On

 %. The initial valve setting when the 

boiler turns on.

b.Specify 

Out Min

 in Volts for the injection device. 

(commonly 2 VDC).

c. Specify Out Max in Volts for the injection device. 

(commonly 10 VDC).

d.Press 

Save

.

NOTE:

 DO NOT change factory Ramp up, 

Ramp Down or KP/KI settings. Please review 

ZXU Application Guide

 and 

Factory KP/KI Set-

ting White Paper

 #508-001.

10.Press 

NEXT 13

 at bottom of screen.

11.Press 

Constant Circ Pump

.

12.The 

Constant Circ Pump

 menu opens.

a.Select “On” or “Auto.” When set to “Auto” zone 

pump comes on with demand; when set to “On” 
pump remains on at all times.

b.Press 

Save

.

13.Press 

Pump Exercise

.

Содержание iWorx ZXU1

























Отзывы: