Taco Comfort Solutions SCX1740 Series Скачать руководство пользователя страница 8

8

TROUBLE AND CAUSE

REMEDY

FAILURE TO PUMP

1. Pump not properly primed.

1. Make sure pump casing and suction line are full of water.

See priming instructions.

REDUCED CAPACITY AND/OR HEAD

1. Air pockets or leaks in suction line.

1. Check suction piping.

2. Clogged impeller.

2. Remove and clean.

PUMP LOSES PRIME

1. Air leaks in suction line.

1. Check suction piping

2. Excessive suction lift and operating

2. Move pump nearer to water level.

too near shut-off point.

3. Water level drops while pumping,

3. Check water supply. Add length of pipe to suction

uncovering suction piping.

to keep submerged end under water.

MECHANICAL TROUBLES AND NOISE

1. Bent shaft and/or damaged bearings.

1. Take motor to authorized motor repair shop.

2. Suction and/or discharge piping not

2. See that all piping is supported to relieve strain

properly supported and anchored.

on pump assembly.

TROUBLE - CAUSES AND REMEDY

COMMERCIAL PUMP WARRANTY TERMS

(MODELS KV, KS, FI, CI, TA, S1740)

Taco, Inc. will repair or replace without charge (at the Company’s option) any commercial pump product or part which is proven to be defective under nor-
mal use within one year from date of start-up or one year and six months from date of shipment (whichever occurs first).
In order to obtain service under warranty, it is the responsibility of the purchaser to promptly notify the Company in writing and promptly deliver the item

 

in question, delivery prepaid to the factory. For complete details on warranty returns, the purchaser should contact a local Taco stocking distributor or the

 

Company. If the product or part in question contains no defect as covered in this warranty, the purchaser will be billed for parts and labor charges in effect

 

at time of factory examination and repair.
Motors provided on commercial pumps are not covered by this warranty, and are warranted by the motor manufacturer. For complete details on motor war-
ranty returns, the purchaser should contact the motor manufacturer’s local service repair center or contact the motor manufacturer directly.
Seals provided on commercial pumps are not covered by this warranty.
Any Taco product or part not installed or operated in conformity with Taco instructions or which has been subjected to misuse, misapplication, the pres-
ence of certain chemicals (such as solvents, acids, etc.) or other abuse will not be covered by this warranty. For complete information on chemical and

 

application restrictions, the purchaser should contact the company.
Taco, Inc. reserves the right to make changes in details of design, construction, or arrangement of materials of its products without notification.
TACO, INCORPORATED OFFERS THIS WARRANTY IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. NO WARRANTIES ARE MADE FOR

 

MERCHANTABILITY OR FITNESS FOR USE AND THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION CONTAINED HEREIN.

 

TACO, INC. WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Taco, Inc.

1160 Cranston Street, Cranston, RI

 

02920 • (401) 942-8000

Содержание SCX1740 Series









Отзывы: