TACKLIFE PPGJ01A, Руководство пользователя, Страница: 8 / 11

WARNING
：
Indicates a potentially hazardous situation,which ,if not avoided,could result in death or
serious injury and/or property damage.
CAUTION: Indicates a potentially hazardous situation,which,if not avoided,may result in minor or
moderate injury and/or property damage.
NOTICE: Indicates a potentially hazardous situation,which,if not avoided,may result in minor or moder-
ate injury and/or property damage.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING Read all safety warnings and all insituations.Failure to follow the warnings and instruc-
tions may result in electric shock ,fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term power tool in the warnings refers to your mains-operated(corded)power tool or battery-operat-
ed (cordIess) power tooI.
1)
a)
b)
c)
2)
a)
b)
c)
d)
e)
f)
3)
a)
b)
c)
d)
e)
f)
g)
4)
a)
b)
c)
d)
e)
f)
g)
5)
a)
ADDITIONAL SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Further Safety Instructions for All Operations
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating wheel,backing pad,brush or anyother
accessory.Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of
the binding.
For example,if a polishing mop is snagged or pinched by the workpiece,the edge of the mop that is
entering into the pinch point can dig into the material causing the mop to climb out or kick out.The mop
may either jump toward or away from the operator.depending on direction of the mop's movement at the
point of pinching.Polishing mops may also break under these conditions.
Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below:
1)
2)
3)
4)
5)
Additional Specific Safety Instructions for Polishers
•
•
•
•
•
Minimum Gauge for Cord Sets
Your risk from these exposures varies,depending on how often you do this type of work.To reduce your
exposure to these chemicals:work in a well ventilated area and work with approved safety equipment
，
such as those dust masks that are specially designed to filter out microscopic particles.
•
WARNING:ALWAYS use safety glasses.Everyday eyeglasses are NOT safety glasses.Also use face
or dust mask if cutting operation is dusty.ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
•
•
•
WARNING
：
Always wear proper personal hearing protection that conforms to ABSI S12.6 (S3.19)
during use.Under some conditions and duration of use,noise from this Droduct may contribute to
hearing loss.
WARNING
：
Some dust created by polishing contains chemicals known to the state of California to
cause cancer birth defects or other reproductive harm.Some examples of these chemicals are:
•
•
•
WARNING:
Use of this tool can generate and/or disperse dust,which may cause serious and perma-
nent respiratory or other injury.Always use NIOSH/OSHA approved respiratory protection appropriate
for the dust exposure.Direct particles away from face and body.
CAUTION
：
Use extra care when working into a comer because a sudden,sharp movement of the
polisher may be experienced when the polishing mop or other accessory contacts a secondary surface
or a surface edge.
BEFORE FIRST USE
CAUTION: ENSURE TOOL IS UNPLUGGED FROM THE MAINS SUPPLY
ASSEMBLING THE HANDLE
The Front Handle or D Type Handle must be fitted to the machine before use:
1.
2.
FITTING THE BACKING PAD
The Backing Pad must be securely fitted to the Spindle before use:
1.
2.
WARNING! The backing pad is tightened by hand.Take care not to cross thread or over-tighten.
Release the spindle lock button
OPERATION
WARNING! Always use adequate protective equipment, including eye protection, respiratory protec-
tion and hearing protection, when working with
this tool.
1.
2.
3.
4.
5.
NOTE: This Polisher is fitted with a Soft Start Function to help spread polish slowly before going to full
speed.
WARNING: Always wait until the machine has come to a standstill before putting it down.
ON/OFF SWITCH
WARNING
：
To reduce the risk of injury,make sure the polisher is not resting on the workpiece when
the switch is turned on.
To turn the polisher on.push the lever of the switch towards the body of the tool;if the polisher is to be
locked in ON position,press button at the same time and keep it pressed while releasing lever,thus
locking the switch.
To turn the polisher off,release the lever or,if locked in ON position,push the lever to release the lock
button.
OPERATION
WARNING
：
To reduce the risk of injury,turn unit off and removing accessories,before adjusting or
when making repairs.Be sure the switch is in the "OFF"position.An accidental start-up can cause
injury.
WARNING
：
Never modify any parts of the power tool.Damage or personal injury could result.
ASSEMBLING THE POLISHING MOP
Press the polishing mop to attach it to the back-up pad.
CAUTION : Accessories must be rated for at least the speed recommended on the tool warning
label.Accessories running over rated speed can fly apart and cause injury.Accessory ratings must
always be above tool speed as shown on tool nameplate.
BEFORE STARTING THE POLISHER
Ensure that:
•
•
•
•
•
FAILURE TO START
Should your tool fail to start,check to make sure the prongs on the cord plug are making good contact in
the outlet.Also,check for blown fuses or open circuit breakers in the line.
REPLACING THE POLISHING MOP
Pull the used polishing mop off and apply the new one,pressing it onto the disc pad.
CAUTION
：
Accessories must be rated for at least the speed recommended on the tool warning label .Acces-
sories running over rated speed can fly apart and causes injury.Accessory ratings must always be above
tool speed as shown on tool nameplate.Press the polishing mop to attach it to the back-up pad.
MAINTENANCE
Maintenance and cleaning of the inner parts,like brushes,ball bearings,gears etc.or others,must be
carried out only by an authorized customer service workshop.
WARNING: To reduce the risk of injury,turn unit off and disconnect it form power source before install-
ing and removing accessories,before adjusting or when making repairs.Be sure the switch is in the
“OFF”
，
position.An accidental start-up can cause injury.
CLEANING
WARNING
：
Blow dirt and dust out of all air vents with clean,dry air at least once a week.To minimize the risk
of eye injury,always wear ANSI Z87.1 performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
：
parts for the
tool.These chemicals may weaken the plastic materials used in these parts.Use & cloth dampened only
with water and mild soap.Never let any liquid get inside the tool;never immerse any part of the tool into a
liquid.
5.OVERVIEW
1.U-type grip
2.ON/OFF Switch
3.Housing
4.Soft cover
5.Power plug and cable
6.Speed control button
7. Straight handle (optional)
8.Allen wrench
9.Polishing disc
- 07 -