Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • [email protected]
DocID: 516619_516620_15.04.2021
Technical specifications
Transmitter
Frequency of operation
2400 - 2483.5 MHz
Max. transmission power
10 mW
Max. input level
1 V (0 dBV)
Latency
12.5 ms
Range
in free field
50 m
not in free field
30 m
Power supply
USB port
Battery
type
built-in lithium-ion battery
capacity
400 mAh
operating time
5 h
charging time
1.5 h
Dimensions (W
×
H
×
D)
52 mm
×
42 mm
×
16 mm
Weight (w/o external microphone)
35 g
Ambient conditions
temperature range
0 °C…40 °C
relative humidity
20 %…80 % (non-condensing)
Microphones
Sound field
mono
Polar pattern
omnidirectional
Frequency range
50 Hz - 20 kHz
Sensitivity
–40 dB (±3 dB, re 1 V / Pa @ 1 kHz)
Max. sound pressure level (@ 1 kHz)
135 dB
EN
For the transport and protective packaging, environmentally friendly materials have
been chosen that can be supplied to normal recycling. Ensure that plastic bags,
packaging, etc. are properly disposed of. Do not just dispose of these materials with
your normal household waste, but make sure that they are collected for recycling.
Please follow the notes and markings on the packaging.
Dispose lithium batteries only in discharged condition. Remove replaceable lithium
batteries from the device before disposal. Protect used lithium batteries from short
circuits, for example by covering the poles with adhesive tape. Permanently installed
lithium batteries must be disposed of together with the device. Please inquire about
a suitable acceptance point.
This product is subject to the European Waste Electrical and Electronic Equipment
Directive (WEEE) in its currently valid version. Do not dispose of your old device with
your normal household waste. Dispose of this product through an approved waste
disposal firm or through your local waste facility. Comply with the rules and regula-
tions that apply in your country. If in doubt, consult your local waste disposal facility.
Sync 1 and 2
Receiver
Frequency of operation
2400 - 2483.5 MHz
Sensitivity
–81 dBm
Output level
Line Out
1 V
Monitoring
25 - 30 mW
Audio channels item no. 516619
1
×
mono
item no. 516620
2
×
mono or 1
×
stereo
Latency
12.5 ms
Range
in free field
50 m
not in free field
30 m
Power supply
USB port
Gain
steps 0 - 4 switchable (0 - 8 dB)
Battery
type
built-in lithium-ion battery
capacity
400 mAh
operating time
5 h
charging time
1.5 h
Dimensions (W
×
H
×
D)
52 mm
×
42 mm
×
16 mm
Weight (w/o external microphone)
35 g
Ambient conditions
temperature range
0 °C…40 °C
relative humidity
20 %…80 % (non-condensing)
Operating
Connections and operating elements Receiver
#
ö
%&
'()
* +
$
ö
Back clip
#
USB C charging port
$
Main switch, keep pressed for 2 seconds for switching on/off
additional for item no. 516620: Switching mono/stereo
%
Blue indicator LED for pairing
slow flashing:
switching on
fast flashing:
pairing
lighting up:
successfully paired
2
×
fast flashing, then
turning off, in cycle:
lowpass function enabled
&
Green charge status indicator
slow flashing:
battery charging status less than 10 %
lighting up:
charging
turning off:
battery fully charged
'
Button for forced shut-off
(
Gain setting (item no. 516619)
Gain setting channel A (item no. 516620)
)
Pairing button (item no. 516619)
Gain setting channel B (item no. 516620)
*
3.5 mm connection for monitoring (headset output)
+
3.5 mm connection for audio output (line out)
Pairing
The pairing automatically starts after switching on. If you like to pair the devices manually,
keep pressed the pairing button (8) (item no. 516619) or the buttons (7) and (8) (item no.
516620) on the receiver and the pairing button (9) on the transmitter for 3 seconds. The
pairing starts automatically.
Connection
The receiver outputs the audio signal via the 3 5 mm TRRS phone cable or the 3.5 mm
TRS camera spiral cable to the recording device. Please use the cable which is suitable for
your device.
Installation
Install the transmitter or the external microphone on the clothes of the speaker. Install the
receiver with the back clip on the hot shoe of the camera.
Gain setting
The initial gain value is the original volume of the microphone. Press the gain button
once to increase the gain by one step. There are 4 steps in total switchable. When the gain
reaches the highest step, press the button again to return to the initial value.
M/S
#
ö
%&
'()
* +
$
Item no. 516619
Item no. 516620
left
front
right
top
left
front
right
top
