t.a.c. TS-5711-770 850 Series Скачать руководство пользователя страница 8

Страница: 8 / 12

F-23837-5

6. Connect the wires to the terminal block on the base plate. See the wiring diagrams in

Figure-1 . When installing a wire in the terminal block, insert the wire from the top side
of the terminal and secure it by tightening the screw located on the front side of the
terminal block.

Caution:

To prevent damage to the components, do not use excessive force when

mounting the sensor base plate onto the electrical box.

7. Dress the wires down and inside the perimeter of the base plate.

8. Snap the wall plate onto the base plate.

9. Reinstall the cover by inserting its top inside edge over the tab on the base plate and

rotating the cover downward. Press the cover to snap it in place.

Figure-8 Mounting of TS-57011-770 or TS-57011-850 Series on 2" x 4" Electrical Box.

American Standard

Electrical Box

Terminal Block

Wire Feedthrough

Opening

Mounting Screws (2)

(furnished)

Wall Plate

Base Plate

Sensing
Element

Printed Circuit

Board

Cover

Latch

Содержание TS-5711-770 850 Series













Результаты поиска

Содержание TS-5711-770 850 Series

Отзывы:

Бренды по названию

Популярные бренды

t.a.c. TS-5711-770 850 Series, Общее руководство по инструкции

Результаты поиска

Содержание TS-5711-770 850 Series

Отзывы:

Бренды по названию

Популярные бренды