SystemAir SYSHRW 096 Скачать руководство пользователя

Страница: 27 / 46

English

1 2 3 4

MODBUS

RS 485

30m MAXI

RCL

1 2

RS 485

12V GND

CARTE

STORM 2

A- B+

SYSHRW 1

1 2

RS 485

12V GND

CARTE

STORM 2

A- B+

SYSHRW 2

1 2

RS 485

12V GND

CARTE

STORM 2

A- B+

SYSHRW 3

100m MAXI

RCL

The Modbus interface, used to communicate with a GTC, is available as an option, factory

assembled or with a kit.

Caution

The use of the µBMS recall command is not compatible with the modbus communication. The

same terminals and addressing DIPs are used in both connection cases.

Caution

Shielded twisted pair wire must be used for interconnecting wiring. Wire impedance must be

between 100 and 130 Ohms and the wire surface section must be between 0.12 and 0.5 mm² (26

to 20 AWG). Larger wire may be used, but in this case connection to the terminal blocks can cause

problems.

Caution

SysHrw

The MODBUS supervision can be connected to a maximum of 123 appliances.

The maximum distance between the RCL and the first unit is 30 metres.

The maximum distance between the RCL and the furthest unit is 100 metres.

Note

: When MODBUS supervision is used, all the units must have a unique address (see "Addressing

procedure").

123

SYSHRW

MAXIMUM

15.9. MODBUS

Содержание SYSHRW 096















































Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды

SystemAir SYSHRW 096, Руководство по установке и обслуживанию

Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды