SystemAir SYSHRW 096 Скачать руководство пользователя

Страница: 19 / 46

English

SysHrw

13.2.2.2. VENTILATION

: Treated air fan motor.

: MV contactor.

FT3

: MV thermal relay.

13.2.2.3. WATER CIRCUIT

: Water circuit valve (not supplied-available in option).

FDP

: Water circuit inlet / outlet differential pressostat

13.2.2.4. CONTROL AND REGULATION

RCL

: Local control module.

ICT

: Anti-freezing protection sensors.

: Intake air temperature sensor.

LWT

: Outlet water temperature sensor.

: Remote ON/OFF switch, 100 m maximum (Not supplied -Please consult us for longer distances).

CLK

: CLOCK input remote ON/OFF

: Timers

KA4

: Relay

13.2.2.5. REMOTE MANAGEMENT AND PROGRAMMING MODULE KIT (<100M)

µBMS

: Supervision module

13.2.2.6. FAULT REPORTING OPTION

KA2

: Remote fault reporting relay (3 A max / 230 V)

13.2.2.7. ELECTRIC HEATING BATTERY OPTION

FF2

: Fuse carrier for heating

: Heating elements

: Power contactor for heating elements

: Automatic reset safety thermostats.

: Manual reset safety thermostats.

13.2.3. PRESSOSTATS SETTINGS

: Low Pressure fixed setting: 1.5 bar (20 PSI) reset at 2.4bar (35 PSI)

: High Pressure fixed setting: 29 bar (420 PSI) reset at 21 bar (305 PSI).

13.2.4. COLOUR CODE

: Black

: Orange

GNYE

: Green/Yellow

: Brown

: White

: Red

: Blue

: Grey

: Violet

: Yellow

Содержание SYSHRW 096















































Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды

SystemAir SYSHRW 096, Руководство по установке и обслуживанию

Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды