SystemAir SYSHRW 096 Скачать руководство пользователя

Страница: 10 / 46

English

600 mm

200 mm

600 mm

1026

1640

8 SysHrw

9. ELECTRIC SPECIFICATIONS

9.1. ELECTRICAL POWER SUPPLY

A variance of ±10% is acceptable in relation to the operating voltage marked on the appliance’s Maker’s

Plate. Phase imbalance on three phase units must not exceed 2%.

Operating voltages :

400V / 3ph / 50Hz + N (360 Volts mini ; 440 Volts maxi.)

Comments: the stated voltages represent the accepted range. However, certain components may be subject

to premature wear on appliances operating continuously, for extensive periods, on abnormally low or high

voltages.

10. INSTALLATION

10.1. UNIT LOCATION

Install the unit in a location allowing easy removal of the filter and the access panels to the electrical

box/compressor and fan by leaving sufficient free space for servicing personnel to perform

maintenance and repairs. Leave sufficient space for the water, electricity and duct connections.

The installer must ensure that access under the

suspended ceiling is provided, and that sufficient

space is provided for the suspension angle brackets,

the duct attachment collars and the water and

electrical connections.

Provide space under the unit for a siphon on the

condensates drainage pipe. Do not install the unit on

top of pipe work.

Each unit is suspended from the ceiling on four

threaded rods.

Warning!

Do not use rods of a diameter smaller

than M10. The rods must be solidly anchored to the

ceiling and to the ceiling joists.

Arrange the threaded rods in accordance with

the dimensions stated below. The use of nuts

and locknuts is recommended for attaching the

suspension rods to the unit as the unit’s vibrations

may loosen a single nut. The installer is liable for any

damage in the event of this recommendation not

being followed.

To facilitate drainage, the unit must be angled in

both planes towards the condensates drainage pipe.

Содержание SYSHRW 096















































Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды

SystemAir SYSHRW 096, Руководство по установке и обслуживанию

Результаты поиска

Содержание SYSHRW 096

Отзывы:

Похожие инструкции для SYSHRW 096

Бренды по названию

Популярные бренды