2 I56-4019-000
MOUNTING DIAGRAMS:
STROBE WITH UNIVERSAL MOUNTING PLATE
:
STROBE SURFACE MOUNT:
1. Mount plate to back box using screws A, making sure wall
opening is equal to the plate opening.
2. Complete
field
wiring.
3. Insert
locking
rib
into
slot
on
plate.
4. Press into plate, unit will make a “click” when it has locked
into place.
A
A
1. Mount skirt to back box with screws A.
2. Complete
field
wiring.
3. Insert locking rib on unit into slot on skirt.
4. Press into skirt; unit will make a “click” when it has locked
into place.
THE LIMITATIONS OF
The signal strobe may cause seizures.
Individuals who have positive photic
response to visual stimuli with seizures, such as persons with epilepsy, should avoid
prolonged exposure to environments in which strobe signals, including this strobe, are
activated.
The signal strobe cannot operate from coded power supplies.
The strobe must
have an uninterrupted source of power in order to operate correctly. Xi'an System
Sensor Electronics Ltd. recommends that the horn and signal strobe always be used
in combination so that the risks from any of the above limitations are minimized.
Ver. B
WARNING
Note: Please dispose electronic waste following national or local
regulations after being scrapped or replaced. Do not discard.
Screw types used for mounting:
A = 8-32 x 3⁄4 flat head
B = 6-32 x 15⁄16 pan head
4-INCH BACK BOX
LOCKING RIB SLOT
LOCKING RIB
BBS
THREE-YEAR LIMITED WARRANTY
Xi'an System Sensor Electronics Ltd. warrants its enclosed strobe product to be free
from defects in materials and workmanship under normal use and service for a period
of three years from date of manufacture. Xi'an System Sensor Electronics Ltd. makes
no other express warranty for this strobe product. No agent, representative, dealer, or
employee of the Company has the authority to increase or alter the obligations or
limitations of this Warranty. The Company’s obligation of this Warranty shall be limited
to the repair or replacement of any part of the strobe product which is found to be
defective in materials or workmanship under normal use and service during the three
year period commencing with the date of manufacture. After contacting
Xi'an System
Sensor for a Return Authorization number, send defective units postage prepaid to:
Xi'an System Sensor Electronics, Ltd. Repair Department, RA #__________,
28 Tuan Jie South Road, Xi’an Hi-tech Development Zone, 710075 China. Please
include a note describing the malfunction and suspected cause of failure. The
Company shall not be obligated to repair or replace units which are found to be
defective because of damage, unreasonable use, modifications, or alterations
occurring after the date of manufacture. In no case shall the Company be liable for
any consequential or incidental damages for breach of this or any other Warranty,
expressed or implied whatsoever, even if the loss or damage is caused by the
Company’s negligence or fault. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This Warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
LOCKING RIB SLOT
LOCKING RIB
4-INCH BACK BOX
A
A
WALL OPENING MUST
EQUAL PLATE OPENING
The strobe will not work without power.
If power is cut off for any reason, the
strobe will not provide the desired visual warning signal.
The signal strobe may not be seen.
The electronic visual warning signal uses
some high light LED indicators. It flashes at least once every second. The strobe
must not be installed in direct sunlight or areas of high light intensity (over 60
foot candles) where the visual flash might be disregarded or not seen. The strobe
may not be seen by the visually impaired.
Please refer to insert for the Limitations of Fire Alarm Systems
