background image

FIGURE 3.

 

 

C0473-00

TAMPER-RESIST FEATURE

NOTE: Do not use the tamper-resist feature if the removal tool is to be used.

The detector base includes a tamper-resist feature that prevents removal of the 
detector without using a small screwdriver or similar tool.

To activate this feature, use needle-nose pliers to break the tab on the detector 
base as shown in Figure 4A. Then, install the detector.

To remove the detector from the base once the tamper-resist feature has been 
activated, insert a small-bladed screwdriver into the small hole on the side 
of the base and push the plastic lever away from the detector head. (See 
Figure 4B). This allows the detector to be rotated counterclockwise for re-
moval. 

The tamper-resist feature can be defeated by breaking and removing the plas-
tic lever from the base. However, this prevents the feature from being used 
again.

FIGURE 4A. ACTIVATE TAMPER-RESIST FEATURE

PLASTIC LEVER

BREAK TAB AT DOTTED LINE BY

TWISTING TOWARD CENTER OF BASE

SCREWDRIVER TO PRESS PLASTIC LEVER

IN DIRECTION OF ARROW

C0132-00

FIGURE 4B. DETECTOR REMOVAL

PLASTIC LEVER

BREAK TAB AT DOTTED LINE BY

TWISTING TOWARD CENTER OF BASE

USE SMALL-BLADED SCREWDRIVER TO PRESS 

PLASTIC LEVER IN DIRECTION OF ARROW

C0132-01

System Sensor warrants its enclosed smoke detector base to be free from defects in ma-
terials and workmanship under normal use and service for a period of three years from 
date of manufacture. System Sensor makes no other express warranty for this smoke 
detector base. No agent, representative, dealer, or employee of the Company has the au-
thority to increase or alter the obligations or limitations of this Warranty. The Company’s 
obligation of this Warranty shall be limited to the repair or replacement of any part of 
the smoke detector base which is found to be defective in materials or workmanship 
under normal use and service during the three year period commencing with the date of 
manufacture. After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672) 
for a Return Authorization number, send defective units postage prepaid to: Honeywell, 

THREE-YEAR LIMITED WARRANTY

12220 Rojas Drive, Suite 700, El Paso TX 79936 USA. Please include a note describing the 
malfunction and suspected cause of failure. The Company shall not be obligated to repair 
or replace units which are found to be defective because of damage, unreasonable use, 
modifications, or alterations occurring after the date of manufacture. In no case shall the 
Company be liable for any consequential or incidental damages for breach of this or any 
other Warranty, expressed or implied whatsoever, even if the loss or damage is caused by 
the Company’s negligence or fault. Some states do not allow the exclusion or limitation of 
incidental or consequential damages, so the above limitation or exclusion may not apply 
to you. This Warranty gives you specific legal rights, and you may also have other rights 
which vary from state to state.

Please refer to insert for the Limitations of Fire Alarm Systems

REMOTE ANNUNCIATOR (RA100Z)

The remote annunciator is connected between terminals 1 and 3 using the 
spade lug terminal packed with the remote annunciator. The spade lug termi-
nal is connected to the base terminal as shown in Figure 5.

It is not acceptable to have three stripped wires under the same wiring ter-
minal unless they are separated by a washer or equivalent means. The spade 
lug supplied with the model RA100Z is considered an equivalent means. See 
Figure 2 for proper installation.

FIGURE 5. CONNECTION TO REMOTE ANNUNCIATOR TERMINAL

 

STRIPPED WIRE

WIRE WITH SPADE LUG

C0116-00

System Sensor® is a registered trademark of Honeywell International, Inc.

NOTE:

 B501-WHITE, B501-IV, and B501-BL replace the previous model num-

bers B501 and B501A; all are functionally the same.

  

I56-3738-004 

 

 

©2018 System Sensor. 03/07/2018

Отзывы: