Synthesis Technology MOTM-850 Скачать руководство пользователя страница 7

Страница: 7 / 21

SYNTHESIS TECHNOLOGY

PAGE 7

MOTM-850 ASSEMBLY 10/25/01
WWW.SYNTHTECH.COM

Shake the board a couple of times, blot dry with an old towel (the leads will frazzle

a good towel). Let dry at least 15 minutes.

Take a little break! You are about 1/3rd of the way finished.

PART #3: CAPACITORS

Locate

the

CAPACITOR

bag.

Locate the 0.1mfd axial ceramic caps (6) and solder into C1, C2, C4, C5, C9 and C10.
Note that these are bent on 0.3” centers.

Locate the 10

fd electrolytics (4). Note that there is a stripe on the NEGATIVE

terminal. The pc board has a + on the POSITIVE terminal. Carefully stick the
capacitors into C3, C6, C7 and C8 with the stripe

away

from the + pad on the board.

All the capacitors will ‘face’ the SAME DIRECTION.

PART #4: MISC and IC STUFF

Almost done with the parts on the pc board! This will finish up the soldering with the
organic flux.

Locate

the

MISC

bag and the

bag.

Locate the ferrite beads (2). They are axial parts, gray colored with no markings.
These are non-polar, and are soldered into L1 and L2 (by JP1).

Locate the MTA-156 power connector. Solder into JP1. Note that the connector has

a ‘locking tab’ on one side. This side is the “inside” facing relative to the pc board.

Note the silkscreen symbol for JP1 has a line on one side, indicating this is the side

where the locking tab goes.

Locate the MXL1013 op amp. Solder into U4. Note that all ICs are pointing “up”
towards the top edge of the pc board (if you call where the pots are the ‘bottom’
edge). The IC will have a ‘notch’ or indentation in the top by Pin #1.

Locate the LM311 comparator. Solder into U1.

Locate the 2N3904 transistor.

DO NOT GET IT CONFUSED WITH THE 2

VOLTAGE REGULATORS!!

Solder into Q1.

Содержание MOTM-850






















Результаты поиска

Содержание MOTM-850

Отзывы:

Бренды по названию

Популярные бренды

Synthesis Technology MOTM-850, Руководство пользователя

Результаты поиска

Содержание MOTM-850

Отзывы:

Бренды по названию

Популярные бренды