background image

 

CIPHER 1160/1260 Bluetooth Wireless Scanner 

 

User’s Manual 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Document Number : 1X60-0200 
Release Date : Nov 20, 2003 

 2003, SYNTECH INFORMATION Co., Ltd.. 

All rights reserved. CipherLab is a registered trademark of SYNTECH 
INFORMATION Co., Ltd. 

 

WARNING 

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try correct the 
interference by one or more of the following measures: 

• 

Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver. 

• 

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 

• 

Consult the dealer or an experienced radio/TV technician for help. 

Содержание CIPHER 1160





















Отзывы: