Syneron Candela VelaShape III Скачать руководство пользователя страница 34

Страница: 34 / 86

Operating Instructions

PB81499EN

When you 'pull up' the

Options

tab the

Treatment Settings

ribbon appears. The

numbered tags in Figure 17 correlate to the following numbered explanations and
definitions of the screen’s elements.

Figure 17: Treatment Settings Ribbon

IR Level

– using your finger to 'tap' on the

(Infra-Red) button in order to

toggle between these intensity levels:

RF Level

– using your finger to 'tap' on the

(Radio-Frequency) button in

order to toggle between these intensity levels:

VAC Level

– using your finger to 'tap' on the

VAC

(Vacuum) button in order

to toggle between these intensity levels:

. The large electrode cover

has four vacuum intensity levels.

End Treatment

– press this button to end the patient's session, reset the

clocks and be ready for the next patient.

Utilities

– for use only by Syneron-trained system engineers, or under direct

instructions from the Syneron Service Center.

Содержание Candela VelaShape III























































































Результаты поиска

Содержание Candela VelaShape III

Отзывы:

Syneron Candela VelaShape III, Руководство пользователя системы, Страница: 34 / 86

Результаты поиска

Содержание Candela VelaShape III

Отзывы: