Syneron Candela VelaShape III Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 86

Syneron Candela VelaShape III Скачать руководство пользователя страница 23

VelaShape III User Manual System Installation

PB81499EN

23

4. S

YSTEM

I

NSTALLATION

The system is designed for installation in a clinical environment. The customer
will carry out the installation as described in the following sections.

Unpacking the System

After unpacking the system, Syneron recommends that you retain the shipping
box and the internal Styrofoam covers and braces in the event that the system will
have to be relocated anytime in the future.

Unpack the system as follows:

1.

Cut off and remove the plastic straps that encase the cardboard box.

2.

Lift the cardboard box up and off the packaged components and set it aside.

Refer to Figure 9:

3.

Carefully remove the packed accessories box from inside the Styrofoam
brace.

4.

Finish removing all of the Styrofoam braces from around the system console.

5.

Remove the plastic bag that is wrapped around the system console.

Figure 9: Unpacking the System

«
...
21
22
23
24
25
...
»

Содержание Candela VelaShape III























































































Отзывы:

Нет отзывов