manualshive.com logo in svg

Synergy 999-308, Инструкция по эксплуатации

Поделиться
Скачать
Synergy 999-308 Скачать руководство пользователя страница 28

320-410 Spur Gear Hub

305-152 52T Spur Gear

103-256 M2.5x6 Cross Recess

305-119 119T Main Gear

101-308 M3x8 Button Head x4

610-151 Auto Hub Delrin Shim

200-407 Auto Hub Assembly

610-151 Auto Hub Delrin Shim

610-147 Auto Hub Sleeve

Note - Do not use grease inside 

auto hub assembly. Please use 

light oil such as Triflow.

IMPORTANT - PLEASE READ!!!

Reverse

Orientation

Factory Auto Hub  Orientation

Main Gear and Spur Gear Assembly

IMPORTANT! - Do not over tghten bolts. 

You may crack delrin gears by over tightening.

Note - By design the auto hub is symmetrical so it can

be used in both orientations. The One-Way Clutch Bearing 

can be pressed into the Auto Hub in any direction. Please 

pay attention to motor direction and insert auto hub sleeve 

in the correct orientation. Your auto hub may be assembled

opposite from the picture. This is perfectly normal!!! Do not 

attempt to press the one way bearing out of the auto hub!

IMPORTANT - PLEASE READ!!!

Page 26

WWW.SYNERGYRCHELICOPTERS.COM

Содержание 999-308
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды