Synapse DIM10-250-11 Скачать руководство пользователя страница 1

DOC-1000089-B-1 

 

 
 

 
 
 
 

 
 
 
 

 

SPECIFICATIONS 

 

Relay Max Switched Circuit: Zero Cross, 5A

 

 

Dim Control Max Load:

 

20 mA Source/50 mA Sink

 

 

Radio Frequency: 2.4 GHz (IEEE 802.15.4)

 

 

RF Transmission Output Power:

 

+20dBM 

 

Operating Temperature:

 

-40 to +70 C 

 

Operating Humidity: 10 to 90%, non-condensing 

 

Configuration/Programming: Stored in non-volatile

 

 

 

 

        memory

 

 

Dimensions: 8.2L x 2.3W X 1.3H in 

 

 

 

(209 X 59 X 33 m)

 

 

Enclosure Type: Galvanneal steel, powder-coated

 

 

 

     white

 

 

CAUTION 

 

DIM10-250-11 controllers must be installed in 

accordance with national, state, and local 
electrical codes and requirements  

 

All work must be performed by qualified 
personnel  

 

Disconnect all power before installation or 
service  

 

Metal conduit connector must be grounded  

 

The switched output 

(LOAD)

 is energized by 

default at power up  

 

Applying excessive force to the terminal blocks 
may result in its failure. 

 

 

 
NEEDED MATERIALS 

 

50 OHM Terminator plug RP-SMA: 

Part 

Number 132360RP from Amphenol

 

 

Wiring Connectors: 

All existing wiring 

connectors must be replaced with new UL 

listed wiring connectors that are correctly 
sized for the application and the number and 

the size of the electrical conductors.

 

 

ATTACHING THE TERMINATOR TO THE 
BULKHEAD 

Make sure the power is off. Attach the 50 OHM 
Terminator to the RP-SMA bulkhead hand tight. Keep 
the 50 OHM Terminator on the bulkhead at all times, 
until the antenna replaces the 50 OHM Terminator. 
When installing the device, the technician must be 
grounded with a proper ground strap. 
 

ATTACHING THE ANTENNA 

When it is time to attach the antenna, touch a 
grounded surface, remove the 50 OHM Terminator and 
screw on the antenna tightly. Tighten a 1/4 turn with a 
pair of needle nose pliers. Do not overtighten or the RF 
pin in the bulkhead will crack, creating poor RF link 
quality. 

 

MOUNTING 

It is critical to the performance of this device that the 
antenna be oriented vertically. It must point straight up 

or down for proper operation. When installing the 
DIM10-250-11 in an enclosure, antenna position must 
be considered in order to provide optimum wireless 

signal strength. For best transmission, all antennas 

should be oriented in the same direction. 

NOTE:   See the DIM10-250-11 mounting template for 

assistance. 

NOTE: Mount in an LED Fixture or Troffer. 

Option A. 

For standard installation: place the light 

controller in the desired location and secure it 
using (4) #8 screws. Prior to permanently 

mounting it, make sure the antenna points 
directly upward or downward and is free of 

any metal objects within 12 in. of the antenna 

(Figure 1). 

Option B. 

For installation in a light pole: hang the light 

controller with an appropriate cable hook, by 
using the cable hook hole at either end of the 

device (Figure 2). 

 

 

 

WARNING AND CAUTIONS: 

TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER 

AT CIRCUIT 

BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!

 

Risk of Electric Shock - 

More than one disconnect switch may be required to 

de-energize the equipment before servicing. 

 

To be installed and/or used in accordance with appropriate electrical codes and 

regulations. 

 

If you are unsure about any part of these instructions, consult an electrician; 
all work should be performed by qualified personnel 

Use this device with copper or copper clad wire only. 

DIM10-250-11 Lighting Controller 

0-10V CONTROL, 2 ANALOG INPUTS 

Load Ratings: 5A @ 100-277VAC (+/- 10%), 50/60 Hz 

Operating Temperature: -40 to +70 C / Operating Humidity: 10 to 90%, non-condensing

 

WARNING AND CAUTIONS:

 

Disconnect power at circuit breaker or fuse when servicing, installing or 
removing fixture or changing lamps. 

Switched output is energized by default at power up 

Mounting:

 It is critical to the performance of this device that the antenna be 

oriented vertically. It must point straight up or down for proper operation. 

Wiring Connectors:

 All existing wiring connectors must be replaced with new 

UL listed wiring connectors. All wiring connectors must be correctly sized for 

the application and the number and the size of the electrical conductors. 

INSTALLATION GUIDE 

 

Отзывы: