Symmetricom TimeProvider 500 series Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 165

background image

Issue 2: Sep 99

TMSL 097-44018-26

Page 153

Table F. Alarm/Event Summary

<aid>

<condtype>

<conddescr>

Severity

Service

Affecting

Notes:
1. The severities in this table are defined as follows:

MN

= minor alarm

SC

= standing condition

MJ

= major alarm

TC

= transient condition

NA

= not alarmed

2. The service-affecting states are: service affecting (SA) and nonservice affecting (NSA).
3. Up to 6 minutes may be required to detect and report an unequipped condition (UNEQUIPPED: IMPROPER

CARD REMOVAL OR COMM FAILURE) from a GTI or an LTI card. This condition may be caused by card
removal, cable removal, or loss of power to the LPR shelf.

4. An asterisk (*) next to a severity indicates the following:

• The severity can be changed using the SET-ATTR-PORT command
• The severity shown is the factory setting

5. A word enclosed in brackets [ ] may or may not appear as part of the <conddescr>.
6. The IS-NR-STBY condtype for TO cards applies to TO-EA, EA10, EA20, EA10M, EA20M cards only.

CLK-x
(x = 1–2)

ACTIVE

CLOCK IS SUPPLYING SIGNAL

SC

NSA

DRIFT

INPUT IS DRIFTING

MN

NSA

FREERUN

CLOCK FREERUNNING

SC

NSA

HOLDOVER

CLOCK IN HOLDOVER

MN

NSA

INACTIVE

CLOCK IS NOT SUPPLYING SIGNAL

SC

NSA

IS-NR-ACT

IN-SERVICE NORMAL-ACTIVE

SC

NSA

LOCKED

CLOCK CONVERGED ON REFERENCE INPUT

SC

NSA

NOT-LOCKED

CLOCK NOT CONVERGED ON REFERENCE
INPUT

SC

NSA

OOS-MT

OUT-OF-SERVICE MAINTENANCE

SC

NSA

OOS-MT-FLT

OUT-OF-SERVICE MAINTENANCE-FAILED

MJ/
MN

SA

TOLERANCE

SYSTEM INPUT TO CLOCK OUT OF TOLERANCE

MN

NSA

UNEQUIPPED

IMPROPER CARD REMOVAL

MN

NSA

DCIM-x
(x = 1–2)

ACTIVE

CARD IS SUPPLYING A SIGNAL TO THE
CLOCK(S)

SC

NSA

ALL-REF

LOSS OF ALL EXTERNAL INPUT REFERENCES

MJ

SA

CLOCK-x
(x = 1–2)

LOSS OF CLOCK SIGNAL

MN

NSA

FAIL

CARD FAIL:CLOCK SYNTHESIZER FAILURE

MJ

SA

FAIL

CARD FAIL: FRAMER FAILURE

MJ

SA

INACTIVE

CARD IS NOT SUPPLYING A SIGNAL TO THE
CLOCK(S)

SC

NSA

«
...
151
152
153
154
155
...
»

Содержание TimeProvider 500 series






































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TimeProvider 500 series

Compact RDMS Telemetry Receiver-Combiner

Бренд: Quasonix Страницы: 152

Бренд: Observator Instruments Страницы: 106

Log NFC Temperature Logger

Бренд: Kaye Страницы: 4

Бренд: JERICHO Страницы: 16

Бренд: Xylem Страницы: 18

Бренд: Huawei Страницы: 180

Бренд: Campbell Страницы: 32

Бренд: Tinytag Страницы: 5

Бренд: scigiene Страницы: 66

MicroRX Station RX2101

Бренд: Hobo Страницы: 25

Бренд: NeuLog Страницы: 4

Бренд: NeuLog Страницы: 4

Бренд: NeuLog Страницы: 6

Бренд: Newland Страницы: 33

Бренд: Newland Страницы: 60

Бренд: Newland Страницы: 66

Бренд: Newland Страницы: 69

Бренд: Dranetz Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды