background image

www.symetrix.co 

| +1.425.778.7728

2 of 4

QUICK START GUIDE:

 Control Server

Software Installation

Composer is the software that provides real-time set-

up and control of Control Server from a Win dows PC 

environment.
Use the following procedure to install Composer on your 

computer.

From the Symetrix web site (http://www.symetrix.co):

1. Download the Composer software installer from the 

Symetrix web site.

2. Double-click on the file you just downloaded and follow 

the on screen directions to install.

After installing the software, refer to the Help File for full 

connection and configuration information.

Network Setup

About DHCP

Control Server boots with DHCP enabled by default. This 

means that as soon as you connect it to a network, it will 

look for a DHCP server in order to obtain an IP address. If 

a DHCP server is present, Control Server will obtain an IP 

address from it. This process may take several minutes. 

With your PC attached to the same network, and thus 

getting its IP address from the same DHCP server, all will 

be ready to go.
If your network does not have a DHCP server, Control 

Server will not be able to obtain an IP address. While 

waiting, Control Server will default to a private IP address 

in the range of 169.254.x.x where x.x is the last four 

alphanumeric characters of Control Server’s MAC address 

(MAC address hex value is converted to decimal for IP 

address). Control Server’s MAC address can be found on 

a sticker on the bottom of the hardware.
When there is no DHCP server present to assign IP 

addresses to either Control Server, or your PC, you may 

need to configure your PC with a static IP in the range of 

169.254.x.x with a Subnet Mask of 255.255.0.0 in order 

to communicate with Control Server in a direct connect 

mode. However, if your PC is using the default network 

settings, it should also have automatically self-assigned a 

similar private IP address in the range of 169.254.x.x, and 

if this is the case, you should be able to connect to Control 

Server directly.
Even if the PC’s default settings have been changed, Control 

Server will try to establish communications by setting up 

appropriate routing table entries to reach devices with 

169.254.x.x addresses.

Connecting to Control Server from a host 

computer on the same LAN

Both Control Server, and the host computer require the 

following 3 items:
1. IP Address - The unique address of a node on a 

network.

2. Subnet Mask - Configuration that defines which IP 

Addresses are included in a particular subnet.

3. Default Gateway (optional) - The IP address of a device 

that routes traffic from one subnet to another. (This is 

only needed when the PC and Control Server are on 

different subnets).

If you are adding Control Server to an existing network, 

a network administrator will be able to provide the above 

information or it may have been provided automatically 

by a DHCP server. For security reasons, it is not 

recommended to put Control Server directly on the 

Internet. If you do, a network administrator or your Internet 

Service Provider can provide the above information.
If you are on your own private network, directly or indirectly 

connected to Control Server, you may allow Control Server 

to choose an automatic IP address or you may choose to 

assign it a static IP address. If you are building your own 

separate network with static assigned addresses, you may 

consider using an IP Address from one of the “Private-Use” 

networks noted in RFC-1918:
1. 172.16.0.0/12 = IP Addresses 172.16.0.1 through 

172.31.254.254 and a Subnet Mask of 255.240.0.0

2. 192.168.0.0/16 = IP Addresses 192.168.0.1 through 

192.168.254.254 and a Subnet Mask of 255.255.0.0

3. 10.0.0.0/8 = IP Addresses 10.0.0.1 through 

10.254.254.254 and a Subnet Mask of 255.0.0.0

Connecting to Control Server through a Firewall/

VPN

We have successfully tested control of Control Server 

through a firewall and VPN, but are unable to guarantee 

performance of these types of connections at this time. 

Configuration instructions are specific to each firewall and 

VPN, so specifics are not available. Additionally, wireless 

communications are also not guaranteed, though they 

have also been successfully tested.

Содержание Control Server

Страница 1: ...ding when handling exposed I O terminals 11 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 12 Only use attachments accessories specified by the manufacturer 13 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use cau...

Страница 2: ...o Control Server directly Even if the PC s default settings have been changed Control Server will try to establish communications by setting up appropriate routing table entries to reach devices with 169 254 x x addresses Connecting to Control Server from a host computer on the same LAN Both Control Server and the host computer require the following 3 items 1 IP Address The unique address of a nod...

Страница 3: ...ER V 8 POWER V Note The ARC Audio line may be grounded at the Symetrix rack mount device and the ARC wall panel to provide additional distance ARC PORT PINOUT 8 7 6 5 4 3 2 1 Pair 1 Pair 3 Pair 4 Pair 2 or or Declaration of Conformity We Symetrix Incorporated 6408 216th St SW Mountlake Terrace Washington USA declare under our sole responsibility that the product Symetrix Control Server to which th...

Страница 4: ... to scratches and dents unless failure has occurred due to a defect in materials or workmanship within the warranty period 7 Conditions caused by normal wear and tear or otherwise due to the normal aging of Symetrix products 8 Damage caused by use with another product 9 Product on which any serial number has been removed altered or defaced 10 Product that isn t sold by an authorized Symetrix Deale...

Отзывы: