Symbol SE 923 Скачать руководство пользователя страница 219

Страница: 219 / 238

B-7

Miscellaneous Code Information

•

Bar codes within a range of lengths

•

Any length of bar codes.

Table B-4 lists the requirements for each option.

Setting Prefixes and Suffixes Via Serial Commands

To append a prefix and suffixes to the decode data:

1. Set the Scan Data Transmission Format (parameter 0xE2) to the desired option.

2. Enter the required value(s) for Prefix (0x69), Suffix1 (0x68) or Suffix2 (0x6A) using

the hex values for the desired ASCII value from Table B-5

Table B-4. Setting Variable Code Lengths

Code length option

L1 value

L2 value

One discrete length will be decoded

Discrete length to decode 0x00

Two discrete lengths will be decoded

Higher length value

Lower length value

Lengths within a range will be decoded

Lower length value

Higher length value

Any length bar code will be decoded

0x00

Table B-5. Character Equivalents

Scan Value

Hex Value

Full ASCII Code

39 Encode Char.

Keystroke

1000

00h

CTRL 2

1001

01h

CTRL A

1002

02h

CTRL B

1003

03h

CTRL C

1004

04h

CTRL D

1005

05h

CTRL E

1006

06h

CTRL F

1007

07h

CTRL G

1008

08h

CTRL H

Содержание SE 923















































































































































































































































Результаты поиска

Содержание SE 923

Отзывы:

Похожие инструкции для SE 923

Бренды по названию

Популярные бренды

Symbol SE 923, Руководство по интеграции

Результаты поиска

Содержание SE 923

Отзывы:

Похожие инструкции для SE 923

Бренды по названию

Популярные бренды