background image

8

C R D 6 8 0 0   L i t h i u m - I o n  

C r a d l e

Ergonomic Recommendations

Caution:

 In order to avoid or minimize the potential risk of ergonomic injury follow the 

recommendations below. Consult with your local Health & Safety Manager to ensure 
that you are meeting with your company’s safety programs to prevent employee 
injury.

• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.

Regulatory Information

All Symbol devices are designed to be compliant with rules and regulations in 
locations they are sold and will be labeled as required.

Any changes or modifications to Symbol Technologies equipment, not expressly 
approved by Symbol Technologies, could void the user's authority to operate the 
equipment.

Marking and European Economic Area (EEA)

Statement of Compliance for non-radio devices

Symbol Technologies, Inc., hereby declares that this device is in compliance with all 
the applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may 
be obtained from http://www2.symbol.com/doc/

Radio Frequency Interference Requirements

Note: This equipment has been tested and found to comply with the limits for a Class 
A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to 
provide reasonable protection against harmful interference when  the equipment is 
operated in commercial environment. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his 
own expense.

Содержание CRD6800













Отзывы: