5-2
L6200EA
3-1. Setting for 7F and FRENCH
data Values
General
1. Enter the Service mode. (See page 5-1)
2. Press " VOL
p
" button on the Service remote con-
trol unit. Display changes " C/D ", " VCO ", " 7F ",
" FRENCH ", " ACCESS CODE ", " STEREO ", "
VIDEO TONE ", " FM-MODE ", and " AV-OUT " cy-
clically when " VOL
p
" button is pressed.
7F
1. Press " VOL
p
" button on the Service remote con-
trol unit. Then select 7F display.
2. Press " CH
o
/
p
" buttons on the Service remote
control unit. Then choose 7F=FF.
FRENCH
1.
Press " VOL
p
" button on the Service remote con-
trol unit. Then select FRENCH display.
2.
Press " CH
o
/
p
" buttons on the Service remote
control unit. Then choose FRENCH=OFF.
ACCESS CODE ---- set to ON
VIDEO TONE ---- set to OFF
FM-MODE ---- set to OFF
AV-OUT ---- set to OFF
STEREO ---- set to ON
Note:
C/D
and
VCO
data values do not need to be
adjusted at this moment.
3-2. Setting for CONTRAST,
COLOR, TINT, V-TINT and
SHARP data Values
General
1. Enter the Service mode. (See page 5-1)
2. Press " MENU " button on the Service remote control
unit. Display changes " BRIGHT ", " CONTRAST ",
" COLOR ", " TINT ", " V-TINT " and " SHARP "
cyclically when " MENU " button is pressed.
CONTRAST (CNT)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " CONTRAST " (CNT) display.
2. Press " CH
o
/
p
" buttons on the Service remote
control unit so that the value of " CONTRAST "
(CNT) becomes 84.
COLOR (CLR)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " COLOR " (CLR) display.
2. Press " CH
o
/
p
" buttons on the Service remote
control unit so that the value of " COLOR " (CLR)
becomes 58.
TINT (TNT)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " TINT " (TNT) display.
2. Press " CH
o
/
p
" buttons on the Service remote
control unit so that the value of " TINT " (TNT) be-
comes 60.
V-TINT (V-TNT)
1.
Press " MENU " button on the Service remote con-
trol unit. Then select " V-TINT " (V-TNT) display.
2.
Press " CH
o
/
p
" buttons on the Service remote
control unit so that the value of " V-TINT " (V-TNT)
becomes 62.
SHARP (SHARP)
1. Press " MENU " button on the Service remote con-
trol unit. Then select " SHARP " (SHARP) display.
2. Press " CH
o
/
p
" buttons on the Service remote
control unit and select " SHARP ON ".
Note:
BRIGHT
data value does not need to be adjust-
ed at this moment.
4. H f
o
Adjustment
Purpose:
To get correct horizontal frequency.
Symptom of Misadjustment:
If H f
0
adjustment is in
correct, sqew distortion will appear on the screen.
Note:
TP302 --- Main CBA
Use Service remote control unit.
1. Connect Frequency Counter to TP302 and ground.
2. Set the unit to the VIDEO mode which is located be-
fore CH2 and no input is necessary. Enter the Ser-
vice mode. (See Page 5-1)
3. Operate the unit for at least 20 minutes.
4. Press " 2 " button on the Service remote control unit
and select H-ADJ Mode. (By pressing " 2 " button
the display will change from TV AGC to H-ADJ)
5. Press " CH
o
/
p
" button on the Service remote
control unit so that the display will change " 0 " ~ " 7
". At this moment, Choose display one of them from
" 0 " ~ " 7 " when the Frequency Counter shows
15.734 kHz±300Hz or closer.
6. Turn the power off and on again. (Main Power but-
ton on the TV unit.)
Test Point
Adj. Point
Mode
Input
TP302
CH
o
/
p
button
["H-ADJ"] MODE
---
Tape
M. EQ.
Spec.
---
Frequency
Counter
15.734kHz±300Hz
