Playing Audio
Playing a Cassette
1. Adjust the
Tape/Radio
switch to
Tape.
2. Open the
Cassette Door
and insert a cassette tape.
3. Close the
Cassette Door
.
4. Use the cassette player’s controls to play, pause, rewind, and fast forward
audio from the cassette.
5. Turn the
Volume
dial to turn on the radio and adjust to the desired volume.
Power
Overview
Battery Power
For battery power, this unit requires 2 AA sized batteries (not included).
DC Power Input (rated 4.5V)
Using an AC/DC Power Adapter (not included), plug the adapter into a standard
power outlet, and the power cord into the DC Power Input on the unit.
Playing the AM/FM Radio
AM and FM antennas are built into the unit, and FM reception is further improved
with the included earbuds. To improve AM reception, adjust the position of the
unit. To Improve FM reception, insert the earbuds and adjust the wire.
1. Adjust the
Tape/Radio
switch to
Radio.
2. Adjust the
AM/FM
switch to the desired frequency band.
3. Turn the
Volume
dial to turn on the radio and adjust to the desired volume.
4. Adjust the
Tuning
dial to tune the radio.
Features
•
Wirelessly stream music to your Bluetooth enabled speakers or headphone
•
Built-in AM/FM radio
•
Play, fast forward, rewind, stop and record
•
One touch recording
•
Cassette recording from radio/mic
•
Built-in condenser microphone
Includes
•
One set of stereo earbuds
•
Detachable belt clip
CASSETTE TAPE USE:
Larger tapes with at least 45 minutes of playing time (C120) per side are not
recommended. Longer duration tapes pose a greater risk of defect for both the
cassette and the cassette player. Use only high quality tapes with a duration less
than 45 minutes.
Recording
Note:
The recorder only records in Mono, Stereo is not available. The recorder
will automatically set the recording level, the Volume dial does not control the
recording level.
1. Open the cassette door, load a blank cassette, then close the cassette door.
2. When you are ready, press the
Play and Record
buttons at the same time to
begin recording audio.
Do not force the Record button down if a tape’s erase
protection tabs have been removed, this may cause damage to the unit.
3. Press the
Stop
button to stop recording.
Recording will stop automatically if
you reach the end of the tape.
Built-in Mic: remain
within 2.5 ft.
DC 1.5V x 2 PCS
(UM-3, “ AA” SIZE, HP-7, R6)
•
Built-in speaker
•
Headphone jack with stereo earbuds included
•
Power: 2 x ‘AA’ batteries or 120V 60Hz AC adaptor (not included)
•
Auto-stop cassette player/recorder
Bluetooth Transmitter Mode
Pairing to a Bluetooth Speaker
The cassette player can act as a Bluetooth transmitter to a Bluetooth speaker. Follow
the below steps to connect to a Bluetooth speaker and play music from a loaded
cassette.
When using Bluetooth, there is no output from the headphone jack.
When the cassette player is stopped for approximately 30 seconds, the power will be
in Bluetooth Mode again.
1. Turn the
Bluetooth Transmitter Switch
on the side of cassette player to ON position
to activate
Bluetooth Pairing Mode
.
2.
inside rewind button. The pairing process could take up to 30 seconds. For best
results, stay within 3 ft. of the Bluetooth speaker you are pairing to.
3.
turn solid. Your Bluetooth speaker should indicate when the connection has been
made as well. The unit will connect to the closest Bluetooth speaker that is near it.
Note:
If the Bluetooth connection cannot be made successfully within one minute,
Bluetooth Transmitter Switch
to retry the connection.
4. Begin playing music on the cassette player to hear it on the connected Bluetooth
speaker. If you are connected to a Bluetooth speaker with a play/pause button and
do not hear audio, try pressing the play/pause button.
Stop button
to stop the player.
6. Turn the
Bluetooth Transmitter Switch
transmitter mode.
Bluetooth Transmitter Switch
Blue LED Light
