Internal
120
Volt
Timer
size: 290mmW x 565mm H
Color: Black text
July 27, 06
Model: SA 306 (DPST):
120 Volt 40 AMP
Digital Industrial Timer Switch
Double-Pole, Single Throw
Indoor Industrial Timer
Please read this manual, before installing your new Sylvania Timer.
Installation
Step 1
WARNING:
Turn power OFF
at circuit
breaker or remove fuse.
Mount case in a vertical position
using mounting holes provided.
Indoor Timer’s 3 mounting hole location
Mount the timer
in the desired location using the three mounting holes (A,B,C) provided. The best
mounting position for the timer is at eye level with sufficient room for the door cover to swing fully open.
Affix box to wall
The top mounting hole (A) is a slotted type mounting hole, so measure and secure this to the wall with the first (A) screw.
The head of the screw (or fastener) should be slightly larger than the narrow portion of the slotted hole.
Hang the timer on screw A. Screw timer into the wall using the remaining two mounting holes (B & C) to provide
a secure permanent mounting for the timer.
Step 4
Study your wiring diagram
and decide which
knockouts
to use. Select the knockouts to be used for your
wire cable clamp or conduit connector and remove the appropriate knockout. Install the wire cable clamps with locknuts.
You are now ready to mount the timer on the wall.
Step 3
Back of timer unit
Knockout
BATTERY
A
C
B
Neutral
Ground
Jumper wire
(not included)
BATTERY
120 VAC
Input Only
Line
Zip-Set Quick Set-up
Detailed set up and function instructions are on back side of this manual.
Set your area code
Yes- You are DONE!
Find and press “Mode” button, until you see the Zip-Set icon
Then depress & hold the Clear (Zip-Set) button until the display flashes.
1
2
3
Fast Set Up Instructions for Zip-Set™ Timers
to
ZIP-SET
CLEAR
To set
:
use “Reverse” / “Forward” buttons and ON/OFF
to Confirm or Enter.
or
then to set press
Set how many hours after sunset that you wish the fixture to
turn the power off (2, 4, 6, 8, 10, 12, 14 or 16 hrs).
Knockouts
(130mm) W
5.1 inch
(200mm) H
7.9 inch
Indoor timer case
Step 6
Restore power at fuse
box or circuit breaker.
Turn Power ON
Step 7
Test Timer:
Press ON/OFF
Button
Inner circle is fit for 1/2 (3/8) inch
cable clamp wire connector or
conduit
Outer Circle is fit for a 3/4 inch
cable
clamp wire connector or
conduit
Ensure that the timer position and its knockouts are
in line with your planned wiring. Knockouts
are made to industrial standards: 1/2 , 3/8, or 3/4 inch wire
cable clamp connectors and locknuts.
Attach appropriate wire cable clamps to the timer box.
Step 2
Remove
the old timer, identify wiring and
disconnect wires from the timer you are replacing
or
map out a new location
for your timer.
When m
ounting the timer, it is important
that it is in an environment which is free from
excessive contaminant such as oil, moisture, or dirt.
Always mount timer case in a vertical position.
Do not mount indoor timer where rain
or water can get in.
Positioning Timer
This product has passed
ETL testing. It is certified
and
complies with both
U.S. and Canadian
product safety standards.
Thank you for purchasing the SA 306 an Industrial 40
Amp digital Timer.
It is an easy to set up and operate industrial timer with
Zip-Set Auto Sunset On Technology and other
advanced features.
Features:
• Zip-Set Technology; automatically turns lights on at
sunset time – just enter your phone area code.
• 4 independent on/off programmable timers with 1 minute
setting intervals.
• Daylight Savings Time (DST) switch.
• Timers can be set to work weekends(2), weekdays(5), or
all week(7).
• Random function for security.
• Manual Override.
• 40 Amp Heavy Duty Relay
Step 5
PRESSURE PLATE
TERMINAL SCREW
MAKE SURE WIRE
INSULATION CLEARS
PRESSURE PLATE
1. Strip 5/8 inch of the wire insulation.
5/8”
Easy wiring
2. Unscrew, lift and twist plastic protective cover
to access the terminals.
3. Identify your Line and Load wires.
4. Run your wires through the knockouts and
cable
clamp wire connectors (not provided).
5. Connect and tighten the ground wire to
grounding terminal at bottom of case.
7.Insert the wire ends under the proper terminal
plates and tighten the screws firmly.
8. Replace the plastic protective cover.
Caution: Only use for 120 VAC
loading only. Otherwise the
timer can be damaged.
WIRING:
Connect in accordance with Local and
National Electrical Codes (NEC). See
suggested circuit diagram below. DO
NOT USE ALUMINIUM WIRE.
SA306
SA306
SA
30
6
5
Zip-set Technology “Sunset Auto on” is easy to program. The clock is set at the factory to the (212) Eastern time zone so you just need to enter
your area code before using. The timer will automatically adjust for your location to turn your appliances and lighting on at sunset. Your SA 306 will
automatically adjust to the changing sunset times as the year progresses.
Your program settings are protected by the integrated back-up battery; even with brown-outs or black-outs, the Zip-set will store settings and turn
your lights and appliances correctly on at sunset once the electric current resumes.
Zip-Set Technology Auto Sunset On
Illuminated Display and Keypad
Battery Backup (batteries included)
SAFETY WARNING
Ratings:
Total load: 40 Amps Resistive & Inductive, 40 Amps Tungsten & Incandescent, 3 HP, 120VAC 60Hz.
Manufactured by Hardware
Innovations LLC.
Technical Support 888-548-4484
www.hardwareinnovations.com
SA306 - 7 - 2006 V - 2
Made in China
DO NOT USE THE TIMER TO TURN OFF POWER FOR MAINTENANCE
WORK (repairs, removing broken bulbs, etc.). ALWAYS TURN POWER
OFF AT THE SERVICE PANEL BY REMOVING A FUSE OR TRIPPING
THE CIRCUIT BREAKER BEFORE DOING ANY ELECTRIC REPAIRS.
NEVER SUBMERGE THE UNIT INTO WATER.
WARNINGS:
Risk of electric shock
• Connect in accordance with Local and National Electrical Codes.
• Install by qualified electricians only
• Do not open or tamper with actual timer.
• Always connect a ground to the timer case
• Switch off the circuit breaker before cleaning
• Keep children away from timer; lock timer case whenever possible.
Risk of fire
• Always insure input and load voltage are compatible with timer.
• Use only proper size AWG wire per your electrical code specification
• Never USE ALUMINIUM WIRE.
• Do not exceed the recommended electrical ratings
Please make the jumper wire according to the load requirement.
The minimum size wire for a 15 AMP general purpose circuit is
AWG 14 wire. For 20 AMP circuit, use AWG 12 wire. For larger
loads such as dryers, use not less than AWG 10 wire and follow
National Electrical Codes.
Jumper Wire
120 VAC
Input Only
Load 2
Load 1
120 VAC
Input Only
Line (Hot)
“The maximum loading of Load 1 and Load 2 in any circumstance
should not exceed the timer’s maximum rating combined load”
3
NEUTRAL
1
2
Internal
120 Volt
Timer
NEUTRO
Temporizador
Interno De
120 Voltios
LÍNEA
CARGA
LINE
LOAD
5
4
LÍNEA
CARGA
LINE
LOAD
3
NEUTRAL
1
2
Internal
120 Volt
Timer
NEUTRO
Temporizador
Interno De
120 Voltios
LÍNEA
CARGA
LINE
LOAD
5
3
LÍNEA
CARGA
LINE
LOAD
3
NEU
TR
AL
1
2
Int
ernal
12
0
Vo
lt
Tim
er
NEU
TRO
Temp
oriz
ador
Inte
rno
De
120
Vo
ltios
LÍNE
A
CA
RG
A
LINE
LOAD
5
4
LÍNE
A
CARG
A
LINE
LOAD
Model: SA306
Do not remove this plastic protective cover
ALL POWER TO THIS CONTROL MUST BE TURNED OFF AT THE
MAIN PANEL BEFORE INSTALLING OR SERVICING THIS
SWITCH OR THE EQUIPMENT IT CONTROLS.
DO NOT USE ALUMINUM WIRES.
TO WIRE, UNSCREW, LIFT AND SWING. REPLACE AFTER WIRING.
CAUTION
M
ode
l: S
A30
6
Do not r
emo
ve t
hi
s pl
as
tic
pr
ot
ec
tiv
e
co
ver
ALL PO
WE
R TO
THI
S CO
NTR
OL M
UST
BE TU
RN
ED OFF
AT T
HE
MAIN
PA
NEL
BEFORE
INS
TA
LLING
OR S
ERV
ICING THI
S
SWIT
CH OR
THE E
QU
IPM
ENT
IT C
ONT
RO
LS.
DO N
OT
USE
ALU
MINU
M WIRES
.
TO
WIRE,
UNS
CR
EW,
LIFT
AND
SWIN
G. RE
PLA
CE AFT
ER W
IRI
NG
.
CA
UTION
Model: SA306
Do not remove this plastic protective cover
ALL POWER TO THIS CONTROL MUST BE TURNED OFF AT THE
MAIN PANEL BEFORE INSTALLING OR SERVICING THIS
SWITCH OR THE EQUIPMENT IT CONTROLS.
DO NOT USE ALUMINUM WIRES.
TO WIRE, UNSCREW, LIFT AND SWING. REPLACE AFTER WIRING.
CAUTION
Zip-Set is pre-set to the 212 area code (New York City) time zone, so if you live in New York within the 212 area code, you are already finished. Simply press
the “Mode” button to “ZIP” and it will automatically turn on your lights and appliance at sunset and turn off after 6 hours. But if you live in another area code,
please follow Zip-Set area code instructions.
Do not touch the time setting! It must always be set to the Default Preset Factory Time (NYC - (212) local time) for the zip-set program to work.
Setting Zip-Set Telephone Area Code
Understanding the Zip-Set Mode
Clock Setting
(this function is usually used when batteries must be replaced) Set only to Eastern Time- 212 area code.
1. Press and hold the
TIME SET Button
until the display is flashing.
2. Press and hold the
Forward/Hourly Adjust Button
to rapidly advance the time forward, or the
Reverse Button
to rapidly change the time
backward. Release button when the approximate correct Eastern time is displayed. PM Indicator is on the upper right corner of the display.
Note:
While pressing either
Forward/Hourly Adjust
or
Reverse Button
the minutes will begin at a moderate pace, and then get faster. This will
help you in setting the time faster and accurately.
3. Press
the
Forward/Hourly Adjust
or
Reverse Button
repeatedly until the correct Eastern time is displayed.
4. Press
the
On/Off/Enter Button
or wait for approx. 10 seconds to exit time setting mode.
5. Slide
the
DST Switch
to ON to have timer increase the current time by 1 hour for daylight saving time. The DST Indicator is to the right of the display.
Slide the
DST Switch
again to turn it off. Current time will decrease 1 hour.
Calendar Setting
(This function is usually used when batteries must be replaced)
1. Press and hold the
Calendar/7-5-2 Button
until “Y 04” (default) flashes on the display.
2. Press
the
Forward/Hourly Adjust
or the
Reverse Button
to adjust to current year then press
On/Off/Enter Button
or wait for approx. 10
seconds. The display will show month/date and flash.
3. Press
the
Forward/Hourly Adjust
or
Reverse Button
repeatedly until the correct month/date is displayed.
4. Press
the
On/Off/Enter Button
or wait for approx. 10 seconds to exit calendar setting mode.
Note:
While pressing either
Forward/Hourly Adjust
or
Reverse Button
the date will begin at a moderate pace, and then get faster. This will help
you in setting the date faster and accurately.
(Figure D)
Battery Installation
– This unit comes with 2 x CR2032 batteries for time keeping and back-up. You should replace the batteries every 2 years. To replace the
batteries, please follow these steps:
1. Turn power off at circuit breaker to remove fuse.
2. Use a small Philips screw driver to remove screw holding the battery compartment.
3. Use a small flat screw driver gently pry the battery door open. Remove the 2 x old CR2032 batteries.
4. Install 2 x new CR2032 batteries into the battery compartment, making sure that the + and – polarities match up with the diagram printed on the unit.
5. When the batteries are in place, return the battery door its original position and tighten the screws.
6. If you find the timer is not running after installing new batteries, you may need to reset it first. Using the point of a pencil or paperclip, press the
RESET
Button
located on the front panel. You will then need to reset the time and date.
Using Programmable ON and OFF Time Settings
(Figure F)
(Figure E)
The SA 306 has
4 independent programmable ON/OFF time settings
so you can turn
outdoor holiday, landscape and security lighting
, etc. on and off at specific
times.
1. Press
MODE Button
until the “PROG” and “1” icons are displayed.
2. Press
the
Calendar/7-5-2 Button
to select the timer frequency. “7” means the timer will operate all week, “5” for weekdays and “2” for just the weekend.
3. Press
and
hold
the
Program Button
until the display is flashing. (Figure E)
4. The display will change to show the ON time for program 1 and flash. The ON Icon will appear. Press the
Forward/Hourly Adjust
or
Reverse
Button
to adjust the ON time.
5. Press the
On/Off/Enter Button
or wait for approx. 10 seconds. The display will show OFF time, and the Off Icon
will appear. (Figure F) Press the
Forward/Hourly Adjust
or
Reverse Button
to adjust OFF time. Press the
On/Off/Enter Button
once more or wait for approx. 10 seconds to
return to normal mode. Display will change back to show the clock time.
6. To program 2nd, 3rd or 4th timer, just follow step 1-5 but press
MODE Button
until “PROG” and corresponding (“2”, “3” or “4”) icons are displayed.
NOTE:
Do not program the same on and off time when setting programs 1, 2, 3 or 4. You can not set the turn on and turn off to the same time (i.e., Turn on at 5:00
am and turn off at 5:00 am). Doing so will produce an error message on the display. To resolve the error message, change the off time by at least one minute using
the forward or reverse button.
Activating the Programmable timer
1. Press
MODE Button
until one of the program icons appears. That programmed timer is now active. (Press the
Program Button
to view the existing
preset times).
2. There is a simpler way to adjust turn on time by pressing the
Forward/Hourly Adjust Button
. The turn On can be adjusted by +/-90 minutes.
3. If you wish, press the
Random Button
once to activate the random feature. The timer on/off time will flu/-10 to +/-120 minutes randomly. To cancel
this feature, just press the button again.
Battery Replacement
Setting Clock and Calendar
to
PROG
(
PROG
1,2,3,or 4)
ZIP-SET
Set your area code
Yes- You are DONE!
Find and press “Mode” button, until you see the Zip-Set icon
Then depress & hold the Clear (Zip-Set) button until the display flashes.
1
2
3
Fast Set Up Instructions for Zip-Set™ Timers
to
ZIP-SET
CLEAR
To set
:
use “Reverse” / “Forward” buttons and ON/OFF
to Confirm or Enter.
or
then to set press
Set how many hours after sunset that you wish the fixture to
turn the power off (2, 4, 6, 8, 10, 12, 14 or 16 hrs).
NOTE:
When changing batteries, make sure to reset the current time to the correct time in the Eastern time zone.
When you enter your telephone area code, it will then automatically adjust to the proper time for your location/time zone.
If Reset: Zip-Set must have the area code, year and date and Eastern time entered properly to function.
Zip-Set is the easiest way to set a light or an appliance to automatically turn on at sunset. Just set the phone area code where you live, make sure the Zip-Set
mode is activated, and you are finished.
(Light OFF)
(Light ON)
Program Times
to
The SA 306 internal clock is pre-set at the factory to the (212-NYC area code) Eastern time zone. (If you live in another area code other than 212- you need to
change the area code). Simply enter your telephone area code by following these easy steps to have the time adjust to your location:
1. Press the
Mode Button
until “ZIP” appears in the display. (Figure A)
2. Press and hold the
Zip Set/Clear Button
until the display shows the 3-digit area code input mode (Figure B).
3. The 1st digit of the telephone area code should be flashing. Press the
Forward/Hourly Adjust
or
Reverse Button
to adjust it, then press
On/Off/Enter Button
to enter it and edit the next digit. Press the
Zip Set/Clear Button
to go back to / edit the previous digit. Continue until the
correct telephone area code is displayed. (
Note:
For special area code time zones see note below)
4. Once your telephone area code is entered, select a turn off time for the Zip-Set automatic sunset timer (the default turn off time of 6 should flash) (Figure C). You
can have the timer turn off 2, 4, 6, 8 ,10, 12, 14 or 16 hours after sunset. While the turn off time is flashing, press the
Forward/Hourly Adjust
to cycle to
the desired turn off setting, then press
On/Off/Enter Button
to enter it. When DONE appears in the display (Figure D), press
On/Off/Enter Button
to
confirm or wait 10 seconds.
5. Press
Mode Button
to Zip (display icon) to confirm the timer is set for ZIP-SET Auto ON at Sunset.
NOTE:
(1.) After entering the Area codes for certain states, a “C” may appear next to the telephone area code, indicating a central location in the state. Press Forward or
Reverse to toggle to W (West) or E (East) and N (North) or S (South) if needed for proper time setting.
(2.) There are also area codes that may have different time zones; for example the 208 area code; by default will flash PST or by pressing Forward or Reverse will
toggle to MST)
(3.) Telephone area codes can change and may not appear in the timer’s table. Should that occur, please use the closest adjacent area code to set the timer correctly
for your location.
(4.) If a new area code was issued after this unit was manufactured or if you enter an invalid/nonexistent area code, you will get an error message stating 'AREA CODE
NOT FOUND'. Enter the closest correct area code for zip set mode to function properly.
(5.) If the clock/calendar is not correct or time is lost after replacing batteries, zip-Set mode will not function properly. Please see Setting Clock and Calendar (below).
Timer Operation
Manual Override
To override the On or Off settings, press the
On/Off Button
. The override setting will not change the next timed event.
Activate the Zip-Set Sunset timer
1. Press the
MODE Button
until "ZIP" icon is displayed. The Zip-Set sunset timer is set and active.
2. SA 306 once properly set, knows the sunset time of your location. It will automatically turn on at sunset and turn off after your selected duration time of 2,4,6,8,10, 12, 14 or
16 hrs.(see ZIP-Set Telephone Area Code Setting)
3. Press the
Random Button
once to activate the random feature so the timer on/off time will fluctuate b/-10 minutes to +/-120 minutes randomly. To cancel this
feature, just press the button again
(
random disappears
)
.
When your home or office is left unattended, this is an excellent security feature to simulate
household activity and random should be activated.
Activate the Programmable timer
1. Press
MODE Button
until the wanted program icon (
PROG
1,2,3,or 4) is displayed and the chosen timer program will be activated.
2. Press the
Random Button
once to activate the random feature so the timer on/off period will fluctuate b/-10 minutes to +/-120 minutes randomly. To cancel
this feature, just press the button again (random disappears).
Turn off all timer functions:
If you don’t want to use any timer functions, just press the
MODE Button
until "OFF" is displayed.
Confirm timer settings for
ON/OFF:
Press
MODE
, select program then press
PROGRAM button
.
RANDOM
to
OFF
to
PROG
RANDOM
PROGRAM
then
to
Battery
Installation
NOTE:
Display and keypad will illuminate when any key is activated
