- 30 -
EN
This function enables you to set a recording length
simply by pressing
[
I
REC/OTR]
on the unit.
Make sure ...
•
The unit must be turned on.
•
Insert a cassette tape with its erase-prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
NOTES:
•
You
cannot
start OTR with the remote control.
•
Recording starts immediately when
[
I
REC/OTR]
is pressed.
•
When
[
I
REC/OTR]
is pressed 18 times, the unit
returns to the normal recording mode.
•
To stop the OTR operation, press
[
C
STOP]
on
the unit or on the remote control.
•
To show the remaining time, press
[DISPLAY]
on
the remote control so that “OTR” appears on the
TV screen. (It will show up momentarily then dis-
appear.)
•
Recording stops when the display shows 0:00.
•
Please note that in the SLP mode maximum
recording time, assuming the tape is started at the
beginning, is 8 hours using T-160 (or 6 hours
using T-120).
•
If the tape runs out before the end time, the unit
will switch to the stop mode immediately, ejects
the tape and turns itself off.
•
Even if
[POWER]
is pressed during OTR, the unit
continues recording.
1
Select the channel to be recorded
Use
the Number buttons
or
[CH.
K
/
L
]
.
NOTE:
•
If the unit is connected to a cable box or satellite
box, the unit must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box
or satellite box.
2
Select the tape speed
Press
[SPEED]
to select the desired tape speed
(SP/SLP).
3
Begin OTR
Press
[
I
REC/OTR]
on the unit as
many times as needed. The record-
ing length will be determined by
the number of times you press
[
I
REC/OTR]
. Each time it is
pressed, the recording time will be
increased by 30 minutes up to 8 hours.
TV/VCR
OTR (One Touch Recording)
Time(s)
Display
Recording length
1 time
(normal recording)
2 times
0:30
30 minutes
3 times
1:00
60 minutes
17 times
8:00
480 minutes
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
Connect your unit and a source (Playing) VCR using
the following diagram.
1)Insert a pre-recorded video cassette into the source
VCR or camcorder.
2)Insert a blank video cassette or one you want to
record over, into the unit’s cassette compartment.
3)Press
[SPEED]
on remote control for the unit to
select the desired recording speed (SP/SLP).
4)Use
[CHANNEL
K
/
L
]
on the unit until “AUX”
appears on the screen.
5)Press
[
I
REC/OTR]
on the unit.
6)Begin playback of the tape in the source VCR or
camcorder.
NOTE:
•
For best results during copying, use the front
panel controls whenever possible. The remote
control might affect the source VCR’s playback
operation.
7)To stop copying, press
[
C
/
A
STOP/EJECT]
on
the unit, then stop the tape on the source VCR or
camcorder.
TV/VCR
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
F.FWD
D
PLAY
C
STOP
A
EJECT
HEADPHONE VIDEO
L – AUDIO – R
VIDEO
IN
OUT
AUDIO
IN
OUT
L
R
[Fig.8]
[Ex: Source VCR or
camcorder]
Audio/Video
cable
(not supplied)
[This unit]
OTR (2 : 30)
SP
