User Manual
Art.Nr. 208 1ME1
call eASY
English
General
Call Easy
is a mobile call pager based on the Easywave system
from ELDAT. It can learn up to 32 transmitter signals.
When a stored signal is received, the display illuminates to show
a predefined text which has been set with PC software.
Pressing briefly the blue button on the front displays all
received calls. A longer press confirms the current displayed call,
deletes it from the list and sends out a different Easywave signal.
Technical Specs
Scope of delivery
Power Sup.: 5V DC (Micro – USB)
Call Easy Receiver
Channels:
32
Micro-USB Cable
Size:
105 x 65 x 23mm
USB Power Adapter
Weight:
approx. 200g
User Manual
Battery:
Li-Po, 3,7V, 1600mAh Wall Mounting
Normal Use
Receiving Calls
When Call Easy receives a stored signal, it will display the text
and start vibrating and beeping three times. This is repeated
twice after 10s. The first line shows “Calls” and the number of
overall received calls.
Use the blue button with a brief press to toggle between the
received calls.
Confirm Calls
Press and hold the blue button to confirm the current
displayed call. This will delete that call from the list and will
send a signal which can be used to program another
Easywave receiver (for example RCP04).
ON/OFF / Mute
Call Easy can be turn off or set to a “Mute” where no signal is
received anymore. To do this please press and hold the power
button for 3s or the blue button for approx. 10s until „Mute“
is displayed. Do the same again to revert back to normal use
mode.
NOTE: the Mute function is only available when all received
calls are confirmed and the display is dark!
Battery
You can check the current battery percentage status by
pressing the blue button briefly after all received calls are
confirmed (display dark) or in Mute-Mode.
While charging you can additionally see a flash if the blue
button is pressed briefly. Low battery is indicated with “Bat.”
in the display and a repeating tone.
Connect the Call Easy with your computer and run the program.
Click on “Auto Connect” and the program will search for the
Call is Easy. The COM port will be shown if it was found.
Read
Reads all texts from Call Easy and display them.
Write
Writes all displayed texts into Call Easy. Empty fields will
be set to „Room x“ automatically.
Reset
Deletes all texts in Call Easy and changes to default „Room
x“. It will also read and display the texts afterwards.
Clear
Clears all fields in the program (not in Call Easy).
Bat. OFF
This will turn off the low battery indication until the
next restart of the Call Easy, for example when you would like to
send the device.
Deutsch/English
Changes the displayed language (if a Call Easy
is connected it will also change language).
Close
Closes the program.
You can download the program at
.
Sybility GmbH, Kreuzweg 15, 91781 Weißenburg, T: 09141-9131689, F: 09141-9132855, www.sybility.de
Stand 01/2019
Store / Delete transmitters
- Using the paper clip, press the programming button located
within a small hole on the back of the pager (see picture…).
The display will then show „Prog Mode“. Press the blue button
to change to the first memory location. The first line shows the
location number and whether it is “free” or “used” when there
is an already stored signal.
In the second line you can see the programmed text.
- Now press the blue button again for more than 1,5s. The
display changes to „x Learn“ (x is the chosen number) and
Call Easy is now waiting for an Easywave signal.
Learn
- Press the button on the transmitter that you would like to
store.
(NOTE: if there is already a stored signal it will be
overwritten. If the same signal is there the display shows
“is used”!)
- Call Easy will restart now and work with the new signal.
- If you want to store more signals, repeat the procedure.
Delete
- Press the blue button again and hold it depressed until „DEL“ is
shown in the second line.
- Call Easy restarts and the memory location is free now.
Prog.
Program Texts
