manualshive.com logo in svg

SWL SWL IR, Руководство по эксплуатации

Поделиться
Скачать
SWL SWL IR Скачать руководство пользователя страница 10

10

Copyright © 2003, 2004, 2005 by swl-remotes.com,

All rights reserved.

LED Operation

The LED provides feedback on the mode and operation of the SWL IR Remote.  The LED blinks 
slowly whenever there is a communications error or the communications has timed out waiting 
for a response when a response is expected.  This can also occur if the radio is powered off and 
you try to initiate commands.

Communications Error

The LED blinks continuously at a slow rate when the communication times out from the radio, or 
a command is NAK’d.  If the radio power is off and you try to initiate any command but power 
on, the LED will indicate a communications error.  If this occurs on every function and the radio 
is powered on and not responding, check the cable connection to the radio.  

This can also mean that the command is invalid in the current operating condition.

Clear Input

After the 

Mute

 is used to clear key entries the LED will blink twice.

Confirmation of Command

After a valid command has been issued and acknowledged the LED will blink once and go out.  
The LED will appear to be on continuously when the 

CH+/-

 is held in the frequency mode 

because the commands repeat and the LED doesn’t always time out.

Configuration Mode

When you enter the parameter configuration mode, the LED will blink continuously at a fast rate 
until the configuration operation is completed or canceled.

Содержание SWL IR














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды