Swisher ZT18542 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 20

Swisher ZT18542 Скачать руководство пользователя страница 20

REPAIR
MANUAL

MODEL NO.

ZT2350

Each mower has its own model number. Each engine has its
own model number. The model number for the mower will be
found under the seat. The model number for the engine will be
found on the top of the blower fan housing.
All mower parts listed herein may be ordered directly from
Swisher Mower & Machine Co. Inc. or your nearest Swisher
dealer.
All engine parts may be ordered from the nearest dealer of the

engine supplied with your mower

.

WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:

*  PRODUCT – Zero Turn Rider (“Z” Series)
*  SERIAL NUMBER - _______________
*  MODEL NUMBER - _______________
*  ENGINE MODEL NUMBER - _______________

TYPE - _______________

* PART NUMBER WITH PAINT CODE
* PART DESCRIPTION

TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650

SWISHER MOWER & MACHINE CO. INC.

1602 CORPORATE DRIVE
P.O. BOX 67
WARRENSBURG, MO 64093

SWISHER MOWER & MACHINE CO. INC.

swisherinc.com

ZERO TURN HYDROSTATIC DRIVE

“Z” SERIES

ZT18542

«
...
18
19
20

Содержание ZT18542





















Отзывы:

Нет отзывов