Swisher RESIDENTIAL ZTR2466BS-CA Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 24

background image

栐

Ǽ

SERVICE & ADJUSTMENTS

19

Hydro Belt Routing & Replacement

For replacement belt part number refer to Replacement Parts Quick Reference Chart in this manual.

Removal

Disconnect spark plug wire.
Apply parking brake.
Remove both hydro fan covers.
Disconnect wiring from electric clutch.
Remove clutch stop.
Remove the engine-to-deck belt.
Loosen the tension on the idler spring.

If loosening the spring is not enough, disconnect the

idler spring from eyebolt completely.

Remove belt from the engine pulley and from the hydro pulleys.

Replacement

Install new belt by placing it around the hydro pulleys first, then around the idler pulleys and engine

pulley. Refer to routing diagram below.

The belt will be loose at this time.
Tightly secure the belt tension back to its original position.
Reinstall the engine-to-deck belt.
Reconnect wiring to the electric clutch.
Reattach the clutch stop in the groove of the clutch.
Reattach the hydro fan covers.
Check for sufficient tension on all belts.
Reconnect spark plug wire.

1.

Left side hydro

2.

Right side hydro

3.

Hydro belt

4.

Engine pulley / Clutch

5.

Pivoting idler

6.

Idler spring

7.

Idler eyebolt

8.

Inside stationary idler

9.

Large backside stationary idler

10. Small backside stationary idler
11. Clutch stop

Rear of Unit (Bottom View)

5

3

4

11

7

1

10

8

9

6

2

Rotation

«
...
17
18
19
20
21
...
»

Содержание RESIDENTIAL ZTR2466BS-CA

























Отзывы:

Нет отзывов

Похожие инструкции для RESIDENTIAL ZTR2466BS-CA

Бренд: Yard force Страницы: 45

Бренд: DR Страницы: 44

Бренд: Snapper Страницы: 84

Бренд: Elem Garden Technic Страницы: 58

ELM 38/1600 PLUS

Бренд: F.F. Group Страницы: 48

Бренд: Trueshopping Страницы: 107

Бренд: Bad Boy Страницы: 64

Бренд: Stiga Страницы: 296

Бренд: Lastec Страницы: 54

Бренд: Parkside Страницы: 52

Бренд: TYM Страницы: 169

LAWN TRACTOR PE12538LT

Бренд: Poulan Pro Страницы: 44

LX420 13AX60RG744

Бренд: Toro Страницы: 36

Бренд: Kubota Страницы: 143

Cruiser 430 Li 60 Series

Бренд: Stiga Страницы: 415

Бренд: Scotts Страницы: 8

Бренд: Spearhead Страницы: 30

Бренд: Spearhead Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды