Swisher QBT2066 Скачать руководство пользователя страница 6

Страница: 6 / 16

REQUIRED ASSEMBLY

FRONT WHEEL CASTER ASSEMBLY

1. Remove single nut and washers from caster shaft.

2. Place one washer on the shaft of the caster/wheel sub-assembly.

3. Slide same shaft through the bearing/frame with wheel towards the ground.

4. Place the other washer on the shaft; it should be resting on the top bearing.

5. Thread nyloc jam nut onto shaft.

6. Tighten nut snuggly, making sure shaft threads enter the nyloc of the nut.

Over-

tightening of this nut will bind caster.

7. Repeat process for other front side.

REAR WHEEL ASSEMBLY

1. Remove cotter pin from axle.

2. Slide washer [ NB149 ] if necessary and wheel[ valve stem out] onto axle and replace

cotter pin.

3. Bend cotter pin so it will not fall out.

4. Repeat process for other wheel.

OFFSET & CENTER TOW HITCH BAR ASSEMBLY

1. Lay out parts according to the diagram.

2. Insert part 661A into part 662 and pin with the hitch pin (H11).

3. Insert part 661 into part 661A. Choose from the 3 holes to set the desired hitch length.

Pin with a hitch pin.

4. Part 12543TC slides into the front tube of the frame. Choose from the 5 holes to arrange

desired offset. Pin with a hitch pin (H11).

5. Eliminate step 3 for hitching from the center bracket. Only one method can be used at a

time.

CENTER TOWING

POSITION

OFFSET TOWING

POSITION

Bent Pin, Hair Pin

and Receiver

supplied by others.

Existing Rear Hitch.

ATV or Utility

Vehicle Attachment

Instructions

661

12543

H11

Содержание QBT2066

















Результаты поиска

Содержание QBT2066

Отзывы:

Бренды по названию

Популярные бренды

Swisher QBT2066, Руководство пользователя

Результаты поиска

Содержание QBT2066

Отзывы:

Бренды по названию

Популярные бренды