Swing MIURA RS Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 60

Swing MIURA RS Скачать руководство пользователя страница 50

50

Section 09

Storing and looking after the paraglider

the decisive factors in how the fabric

ages. The colours will fade first and
then the coating and fibres will begin
to age.
When the MIURA RS is manufactured,

the side of the fabric with the coating is

kept to the inside. This provides
relatively good protection from

damage for the coating which is of key
importance to the fabric

’s

features.

When choosing a place to launch, try
to find somewhere which is smooth
and free of stones and sharp objects.
Do not stand on the glider. This
weakens the fabric, especially if it is on

a hard or stony surface. Pay attention
to the behaviour of spectators at the

launch site, especially children: do not

hesitate to draw their attention to the
sensitive nature of the fabric.
When you are packing up your glider,
make sure that there are no insects

trapped inside. Many insects produce
acids when they decompose, which

can cause holes in the fabric.

Grasshoppers make holes by biting
through the fabric and also excrete a

dark liquid which stains. Keep animals
away when you are packing up. Insects

are not attracted by any particular
colours, contrary to what is commonly
believed.
A brand-new glider will often be
compressed when delivered. This is

solely for the initial delivery and the
glider should not be compressed in

such a way again. Do not pack your
glider too tightly after use and, even

though it is very comfortable, never sit
on the backpack with the glider inside.

Lines

The MIURA RS has various different
high-quality and accurately

manufactured lines which have been
selected according to the load and

area of use. You should also protect the

lines from unnecessary UV light
because, as with the fabric, UV light in
particular will weaken the lines.
Be careful that there is no abrasion

caused to the coating on the lines by

rubbing, particularly when ground-
training with crossed risers.
Do not walk on the lines after the glider
has been spread out and watch out for

spectators or skiers who may
inadvertently go over the lines.
When you are packing up the glider, be

careful to avoid putting any
unnecessary kinks in the lines and use

only the overhand knot or bowline
knots described for the brake lines.



PLEASE NOTE

Dyneema lines, which are used in
the area of the main brake lines, for

example, are very temperature-
sensitive and can be permanently

damaged at temperatures above 75°
C. Therefore your glider should never

be stored in a hot car especially
during summer

Dampness / humidity

If the glider gets wet or damp, it should
be dried as soon as possible in a well-

ventilated room (but out of the sun). It
may take several days before the

canopy has dried completely because

the fibres absorb water. Mould may
form if the paraglider is stored wet and

the fibres may rot, particularly when it
is warm. This can make the paraglider

unsuitable for flying within a short
time.
Likewise, if a wet glider freezes, it can

also become unsuitable for flying after
a short time.

«
...
48
49
50
51
52
...
»

Содержание MIURA RS





























































Отзывы:

Нет отзывов