background image

3

This product is intended for single family home/residential use only and not intended for use in any public setting. 

Placement in any public setting constitutes a misuse of this product.

IMPORTANT

!

ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS

According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground.  If soil conditions permit

stakes to be pulled out easily, cementing into ground is necessary.

•  To anchor the unit to the ground, 

Follow the instructions included in this plan for applying Anchor-It devices to your unit, or use 2" x 4" x 18" (45mm x 95mm x 457mm) pressure-

treated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and climbing unit posts).  Attach with four (4) 2-1/2’’ 

galvanized screws per stake into each tower and/or A-frame upright. NOTE: Leave the soil around anchors as intact as possible. Do not excavate more soil than is necessary to place 

anchors.

•  If the unit has a climbing rope,

securely anchor the rope at both ends.  

•  Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material must be installed.  

This may be accomplished by

using loose-fill materials at a sufficient depth.  The Consumer Product Safety Commission “Handbook for Public Playground Safety” lists the following materials and required depths

that are sufficient for home/residential application. Supplemental information may be found in ASTM F1292. For fall height protection up to 9 ft. (2.742m) [recommended for

Swing•N•Slide kits]:

LOOSE FILL MATERIAL

REQUIRED (UNCOMPRESSED) DEPTH

1

in. (mm)

Wood Mulch

9" (229mm)

Double Shredded Bark Mulch

9" (229mm)

Uniform Wood Chips

12" (305mm)

These depths were derived from the CPSC Handbook.  Swing•N•Slide has not done independent tests to determine these required depths.

When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units.  This protective surfacing must extend a 

minimum

of 6 ft.

(1.828m) in all directions from the perimeter of the equipment or from the outermost edges of any component.  For example, a slide extending beyond the platform must have protec-

tive surfacing at least 6 ft. (1.828mm) out from both sides as well as the end.  For swings, the protective surface must extend 

at least 14 ft. (6m)

out from 

both

the back and front of

the swing when the swing is in its rest position.

Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY

Swing-N-Slide® takes great pride in the quality and durability of our products.  Our Manufacturer’s Limited Warranty provides confidence and demonstrates our commitment to
providing quality residential playground products.

MANUFACTURER’S LIFETIME LIMITED WARRANTY

Swing-N-Slide® warrants its thermoformed slides and climbing mountains to be free from defects in workmanship and materials, under normal use and conditions, for the 
lifetime of the product.

MANUFACTURER’S 5 YEAR LIMITED WARRANTY 

Swing-N-Slide®

warrants its Custom Ready-to-Build Play Set kits and accessories to be free from defects in workmanship and materials, under normal use and conditions,

for a period of 5 years. 

MANUFACTURER’S 5 YEAR LIMITED WARRANTY

Swing-N-Slide®

warrants its No-Cut and Wood Complete Ready-to-Assemble Play Set kits against wood rot and termite damage, and to be free from defects in workman-

ship and materials, under normal use and conditions, for a period of 5 years for structural wood components. 

Cosmetic defects

that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or any

other physical properties of wood that do not present a safety hazard, are not covered by this warranty.

MANUFACTURER’S ONE YEAR WARRANTY

Swing-N-Slide®

warrants its canopy roofs and/or tarps, playhouses and Timber GLOVE lumber wrap to be free from defects in workmanship and materials, under normal

use and conditions, for a period of one year.

Swing-N-Slide®

will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials.  This decision is subject

to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545.  Any part(s) returned to Swing-N-
Slide® must have prior approved Return Authorization Number and proof of purchase, including the date of purchase.  This warranty is valid only if the product is used for the
purpose for which it was designed and installed at a residential, single family dwelling.  This warranty is void if the product is put to commercial or institutional use.  This 
warranty does not cover (a) products which have been damaged by acts of Nature, negligence, misuse, or accident, or which have been modified or repaired by 
unauthorized persons; (b) the cost of labor; or the cost of shipping the product, any part, or any replacement product or part.

Swing-N-Slide®

DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE 

IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.  Swing-N-Slide® WILL NOT BE LIABLE FOR ANY INCIDENTAL OR 
CONSEQUENTIAL DAMAGES.  This warranty is non-transferable and does not extend to the owners of the product subsequent to the original purchaser.  Some states do not
allow limitations on implied warranties or exclusion of incidental or consequential damages, so these restrictions may not be applicable to you.  This warranty gives you 
specific legal rights.  You may also have other rights, which vary from state to state.

This warranty also does not apply to:

• Structures not erected, maintained or inspected in conformance with 

Swing-N-Slide®

installation plans

• Structures that have had parts added or substituted not in conformance with 

Swing-N-Slide®

installation plans

Parts that have been modified, altered or misused

Parts that have not been used as designed or intended

Damage due to acts of Nature, vandalism, abnormal use or abuse as determined by 

Swing-N-Slide®

For further information on playground safety,

the Consumer Product Safety Commission (CPSC)

publishes the Outdoor Home Playground Safety Handbook which can be downloaded for free from

www.cpsc.gov. An additional resource is the American Society of Testing and Materials (ASTM) 

Standard Consumer Safety Performance Specification for Home Playground Equipment (ASTM F1148)

which can be purchased and downloaded from www.astm.org.

Содержание PB 8137

































Отзывы: