background image

2

Installation Safety 

– Have You:



Consulted the assembly instructions supplied with your particular model?



Consulted the assembly instructions of your particular model for minimum use zones?



Used a water sealant on your play set to protect the wood and prevent cracking and warping?



Placed the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a fence, 
garage, house, overhanging branches, laundry lines, or electrical wires?



Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall 
onto a hard surface can result in serious injury to the equipment user.)



Followed all anchoring and shock absorbing surfacing requirements as they apply?



Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.)



Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with a metal

fi le as needed, and coated fastener ends with lead free paint?



Verifi ed that suspended climbing ropes, chain or cable are secured at both ends?



Made sure not to allow children to use equipment until it is properly installed?



Made sure to adjust all swings so there is a minimum 8’’ clearance between the swing and the ground surface?



Noted this accessory is to be used only on Swing•N•Slide approved designs?

(Do not alter its design or add/remove components.)

Operating Safety 

– Have You:



Determined that on-site adult supervision is provided for children of all ages?



Determined that only one child per planned occupant seat should be allowed on this set at one time.



Determined children must be dressed appropriately for play. Avoid hooded jackets, bicycle helmets, clothing with draw strings 
and loose fi tting clothes which could become entangled or snagged on equipment.



Determined that suspended climbing ropes, chain, or cable cannot be looped back upon itself.



Made certain the slide is placed so that is not in direct sunlight.



Warned children the following before allowing them to use the equipment?

Not to walk close to, in front of, behind or between moving items.

Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the 
strength of chain or rope.

Not to swing empty seats or other accessories.

Not to slide down swing chains.

Be sure to sit in the center of the swing seat and other accessories with full weight on the seat.

Not to attach items to the playground equipment that is not specifi cally designed for use with the equipment such as but not 
limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard.

Not to climb or walk on the top of swing beams, railings or roof.

Not to use equipment in a manner other than intended.

Not to get off equipment while it is in motion.

Not to climb on the equipment when it is wet.

Be sure to go down slides feet fi rst.

Safety Maintenance 

– At the beginning of every season and twice monthly thereafter:



Rake and check depth of loose fi ll protective surfacing material to prevent compaction and maintain appropriate depth. Replace 
as necessary.



Check all nuts, bolts and Quick  Links during the usage season for tightness and tighten as required. (It is particularly important 
that this procedure be followed at the beginning of each season.)



To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories when outdoors temp dips 
down to or below 32° F and take indoors.



Oil all metallic moving parts monthly during usage period.



Check all hardware and equipment for sharp edges during usage season. (Replace when necessary. It is especially important to 
do this at the beginning of each new season.)



Check swing seats, chains, ropes and cables monthly during usage season for evidence of deterioration. Severe rusting or 
excessive wear, especially near the top swing hanger or at the seat connection are evidence of chain deterioration. Cracks in 
the protective plastic sleeve or seat itself are also signs of deterioration. If any of these conditions exist, call 1-800-888-1232 to 
order replacement accessories.



Sand rusted metal parts and repaint using non-lead based paint.



Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members.

Disposal Instructions

When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable
hazards will exist at the time the set is discarded.

Safety Checklist for Swing-N-Slide Playsets & Accessories

Save this instruction sheet in the event the manufacturer needs to be contacted.

Observing the following statements and warnings reduces the likelihood of serious or fatal injury.

Meijer.com

Содержание PB 5200





















































Отзывы: